AD73311LAR Analog Devices Inc, AD73311LAR Datasheet - Page 21
![IC ANALOG FRONT END 20-SOIC](/photos/6/50/65038/505-20-soic_sml.jpg)
AD73311LAR
Manufacturer Part Number
AD73311LAR
Description
IC ANALOG FRONT END 20-SOIC
Manufacturer
Analog Devices Inc
Datasheet
1.AD73311LAR.pdf
(36 pages)
Specifications of AD73311LAR
Rohs Status
RoHS non-compliant
Number Of Bits
16
Number Of Channels
2
Power (watts)
50mW
Voltage - Supply, Analog
3V
Voltage - Supply, Digital
3V
Package / Case
20-SOIC (7.5mm Width)
Single Supply Voltage (min)
2.7V
Single Supply Voltage (max)
3.3V
Package Type
SOIC W
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD73311LAR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD73311LARS
Manufacturer:
AD
Quantity:
12
Part Number:
AD73311LARS
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD73311LARS/AD73311
Manufacturer:
LITEON
Quantity:
10 000
Company:
Part Number:
AD73311LARSREEL
Manufacturer:
STM
Quantity:
6 706
Company:
Part Number:
AD73311LARSZ
Manufacturer:
MIC
Quantity:
6 222
Part Number:
AD73311LARSZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD73311LARSZ-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD73311LARU
Manufacturer:
ADI/亚德诺
Quantity:
20 000
As the AD73311L can be operated at 8 kHz (see Figure 21) or
16 kHz sampling rates, which make it particularly suited for
voiceband processing, it is important to understand the action of
the interpolator’s Sinc3 response. As was the case with the encoder
section, if the output signal’s frequency response is not bounded
by the Nyquist frequency it may be necessary to perform some
initial digital filtering to eliminate signal energy above Nyquist to
ensure that it is not imaged at the integer multiples of the sampling
frequency. If the user chooses to bypass the interpolator, per-
haps to reduce group delay, images of the original signal will be
generated at integer intervals of the sampling frequency. In this
case these images must be removed by external analog filtering.
Figure 22 shows the output spectrum of a 1 kHz tone being
generated at an 8 kHz sampling rate with the interpolator
bypassed.
–100
–100
–10
–20
–30
–40
–50
–60
–70
–80
–90
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
0
0
0
500
0.5
1000
1.0
1500
FREQUENCY – Hz
FREQUENCY – Hz
1.5
2000
2.0
2500
2.5
3000
3500
3.0
4000
10
3.5
4
Decoder Group Delay
The interpolator roll-off is mainly due to its sinc-cubed function
characteristic, which has an inherent group delay given by the
equation:
where:
The analog section has a group delay of approximately 25 µs.
On-Chip Filtering
The primary function of the system filtering’s sinc-cubed (Sinc3)
response is to eliminate aliases or images of the ADCs or DAC’s
resampling, respectively. Both modulators are sampled at a
nominal rate of DMCLK/8 (which is 2.048 MHz for a DMCLK
of 16.384 MHz) and the simple, external RC antialias filter is
sufficient to provide the required stopband rejection above the
Nyquist frequency for this sample rate. In the case of the ADC
section, the decimating filter is required to both decrease sample
rate and increase sample resolution. The process of changing
sample rate (resampling) leads to aliases of the original sampled
waveform appearing at integer multiples of the new sample rate.
These aliases would get mapped into the required signal pass-
band without the application of some further antialias filtering.
In the AD73311L, the sinc-cubed response of the decimating
filter creates spectral nulls at integer multiples of the new sample
rate. These nulls coincide with the aliases of the original waveform
which were created by the down-sampling process, therefore
reducing or eliminating the aliasing due to sample rate reduction.
Order is the interpolator order (= 3),
L is the interpolation factor (= 32 @ 64 kHz, = 64 @ 32 kHz,
= 128 @ 16 kHz, = 256 @ 8 kHz) and
T
=> Group Delay (Interpolator @ 64 kHz)
= 3 × (32 – 1)/2 × (1/2.048e6)
= 22.7 µs
INT
Group Delay (Interpolator) = Order × (L – 1)/2) × T
–100
is the interpolation sample interval (= 1/2.048e6)
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
0
0.5
1.0
FREQUENCY – Hz
1.5
2.0
2.5
AD73311L
3.0
10
3.5
INT
4