AD7908BRUZ Analog Devices Inc, AD7908BRUZ Datasheet - Page 9

• Manufacturer Part Number: AD7908BRUZ
• Description: IC ADC 8BIT 8CH 1MSPS 20-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD7908BRUZ

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Bits: 8
• Sampling Rate (per Second): 1M
• Number Of Converters: 1
• Power Dissipation (max): 13.5mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP (0.173", 4.40mm Width)
• Resolution (bits): 8bit
• Sampling Rate: 1MSPS
• Input Channel Type: Single Ended
• Supply Voltage Range - Analog: 2.7V To 5.25V
• Supply Current: 2.7mA
• Digital Ic Case Style: TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD79X8CBZ - BOARD EVALUATION FOR AD79X8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

TIMING SPECIFICATIONS
AV
Table 4.
Parameter
f
t
t
t
t
t
t
t
t
t
t
t
t
t
1
2
3
4
SCLK
CONVERT
QUIET
2
3
4
5
6
7
8
9
10
11
12
Sample tested at 25°C to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of AV
The 3 V operating range spans from 2.7 V to 3.6 V. The 5 V operating range spans from 4.75 V to 5.25 V.
Mark/space ratio for the SCLK input is 40/60 to 60/40.
Measured with the load circuit of Figure 2 and defined as the time required for the output to cross 0.4 V or 0.7 × V
t
back to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t
time of the part and is independent of the bus loading.
3
3
4
8
is derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 2. The measured number is then extrapolated
DD
2
= 2.7 V to 5.25 V, V
AV
10
20
16 × t
50
10
35
40
0.4 × t
0.4 × t
10
15/45
10
5
20
1
Limit at T
DD
= 3 V
SCLK
SCLK
SCLK
DRIVE
MIN
≤ AV
, T
MAX
AV
10
20
16 × t
50
10
30
40
0.4 × t
0.4 × t
10
15/35
10
5
20
1
DD
DD
AD7908/AD7918/AD7928
, REF
= 5 V
SCLK
SCLK
SCLK
IN
Figure 2. Load Circuit for Digital Output Timing Specifications
= 2.5 V, T
kHz min
MHz max
ns min
ns max
ns max
ns min/max
ns min
Unit
ns min
ns min
ns min
ns min
ns min
ns min
μs max
OUTPUT
PIN
TO
A
= T
50pF
MIN
C
Rev. B | Page 9 of 28
L
to T
200µA
200µA
MAX
Description
Minimum quiet time required between CS rising edge and start of
CS to SCLK setup time
Delay from CS until DOUT three-state disabled
Data access time after SCLK falling edge
SCLK low pulse width
SCLK high pulse width
SCLK to DOUT valid hold time
SCLK falling edge to DOUT high impedance
DIN setup time prior to SCLK falling edge
DIN hold time after SCLK falling edge
16
Power-up time from full power-down/auto shutdown mode
, unless otherwise noted.
th
next conversion
SCLK falling edge to CS high
I
I
OL
OH
1.6V
8
, quoted in the timing characteristics is the true bus relinquish
DD
) and timed from a voltage level of 1.6 V. See Figure 2.
DRIVE
1
.
AD7908/AD7918/AD7928