LTC2420CS8 Linear Technology, LTC2420CS8 Datasheet - Page 29
![IC ADC 20BIT MICRPWR W/OSC 8SOIC](/photos/6/62/66297/8-soic_05-08-1610_sml.jpg)
LTC2420CS8
Manufacturer Part Number
LTC2420CS8
Description
IC ADC 20BIT MICRPWR W/OSC 8SOIC
Manufacturer
Linear Technology
Datasheet
1.LTC2420CS8.pdf
(36 pages)
Specifications of LTC2420CS8
Number Of Bits
20
Sampling Rate (per Second)
7.5
Data Interface
MICROWIRE™, Serial, SPI™
Number Of Converters
2
Power Dissipation (max)
1mW
Voltage Supply Source
Single Supply
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
Q1156784
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTC2420CS8
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC2420CS8#PBF
Manufacturer:
LT
Quantity:
1 200
Company:
Part Number:
LTC2420CS8#PBF
Manufacturer:
Linear
Quantity:
1 100
Part Number:
LTC2420CS8#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC2420CS8#TRPBF
Manufacturer:
LT
Quantity:
1 200
SYNCHRONIZATION OF MULTIPLE LTC2420s
Since the LTC2420’s absolute accuracy (total unadjusted
error) is 10ppm, applications utilizing multiple matched
ADCs are possible.
Simultaneous Sampling with Two LTC2420s
One such application is synchronizing multiple LTC2420s,
see Figure 35. The start of conversion is synchronized to
the rising edge of CS. In order to synchronize multiple
LTC2420s, CS is a common input to all the ADCs.
To prevent the converters from autostarting a new con-
version at the end of data output read, 23 or fewer SCK
clock signals are applied to the LTC2420 instead of 24 (the
24th falling edge would start a conversion). The exact
timing and frequency for the SCK signal is not critical
since it is only shifting out the data. In this case, two
LTC2420’s simultaneously start and end their conversion
cycles under the external control of CS.
TYPICAL APPLICATIO S
SDO1
SDO2
SCK1
SCK2
CS
U
CONTROLLER
Figure 35. Synchronous Conversion—Extendable
23 OR LESS CLOCK CYCLES
SDO1
SDO2
SCK2
SCK1
CS
V
V
V
GND
CC
REF
IN
LTC2420
#1
SDO
SCK
CS
F
O
Increasing the Output Rate Using Multiple LTC2420s
A second application uses multiple LTC2420s to increase
the effective output rate by 4 , see Figure 36. In this case,
four LTC2420s are interleaved under the control of sepa-
rate CS signals. This increases the effective output rate
from 7.5Hz to 30Hz (up to a maximum of 400Hz). Addi-
tionally, the one-shot output spectrum is unfolded allow-
ing further digital signal processing of the conversion
results. SCK and SDO may be common to all four LTC2420s.
The four CS rising edges equally divide one LTC2420
conversion cycle (7.5Hz for 60Hz notch frequency). In
order to synchronize the start of conversion to CS, 23 or
less SCK clock pulses must be applied to each ADC.
Both the synchronous and 4 output rate applications use
the external serial clock and single cycle operation with
reduced data output length (see Serial Interface Timing
Modes section and Figure 7). An external oscillator clock
is applied commonly to the F
order to synchronize the sampling times. Both circuits
may be extended to include more LTC2420s.
23 OR LESS CLOCK CYCLES
V
V
V
GND
CC
REF
IN
LTC2420
#2
SDO
SCK
CS
F
O
EXTERNAL OSCILLATOR
(153,600HZ)
V
(0.1V TO V
O
REF
pin of each LTC2420 in
CC
)
LTC2420
2420 F35
29