LTC2420IS8 Linear Technology, LTC2420IS8 Datasheet - Page 23

• Manufacturer Part Number: LTC2420IS8
• Description: IC ADC 20BIT MICROPOWER 8SOIC
• Manufacturer: Linear Technology

Specifications of LTC2420IS8

• Number Of Bits: 20
• Sampling Rate (per Second): 7.5
• Data Interface: MICROWIRE™, Serial, SPI™
• Number Of Converters: 2
• Power Dissipation (max): 1mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

APPLICATIO S I FOR ATIO
propagation delay from the driver to LTC2420. For refer-
ence, on a regular FR-4 board, signal propagation veloc-
ity is approximately 183ps/inch for internal traces and
170ps/inch for surface traces. Thus, a driver generating
a control signal with a minimum transition time of 1ns
must be connected to the converter pin through a trace
shorter than 2.5 inches. This problem becomes particu-
larly difficult when shared control lines are used and
multiple reflections may occur. The solution is to care-
fully terminate all transmission lines close to their char-
acteristic impedance.
Parallel termination near the LTC2420 pin will eliminate
this problem but will increase the driver power dissipation.
A series resistor between 27 and 56 placed near the
driver or near the LTC2420 pin will also eliminate this
problem without additional power dissipation. The actual
resistor value depends upon the trace impedance and
connection topology.
Driving the Input and Reference
The analog input and reference of the typical delta-sigma
analog-to-digital converter are applied to a switched ca-
pacitor network. This network consists of capacitors switch-
ing between the analog input (V
reference (V
both V
shown in Figure 16.
The key to understanding the effects of this dynamic input
current is based on a simple first order RC time constant
model. Using the internal oscillator, the LTC2420’s inter-
nal switched capacitor network is clocked at 153,600Hz
V
GND
V
REF
I
IN
IN
Figure 16. LTC2420 Equivalent Analog Input Circuit
IN
SWITCHING FREQUENCY
f = 153.6kHz FOR INTERNAL OSCILLATOR (f
f = f
and V
V
CC
EOSC
REF
V
I
I
REF(LEAK)
REF(LEAK)
CC
FOR EXTERNAL OSCILLATORS
REF
). The result is small current spikes seen at
I
I
. A simplified input equivalent circuit is
IN(LEAK)
IN(LEAK)
U
R
R
R
5k
5k
5k
SW
SW
SW
U
IN
), ground (Pin 4) and the
2420 F16
I
IN
W
AVERAGE INPUT CURRENT:
O
= 0.25(V
= LOGIC LOW OR HIGH)
C
1pF (TYP)
EQ
IN
– 0.5 • V
U
REF
)fC
EQ
corresponding to a 6.5 s sampling period. Fourteen time
constants are required each time a capacitor is switched in
order to achieve 1ppm settling accuracy.
Therefore, the equivalent time constant at V
should be less than 6.5 s/14 = 460ns in order to achieve
1ppm accuracy.
Input Current (V
If complete settling occurs on the input, conversion re-
sults will be uneffected by the dynamic input current. If the
settling is incomplete, it does not degrade the linearity
performance of the device. It simply results in an offset/
full-scale shift, see Figure 17. To simplify the analysis of
input dynamic current, two separate cases are assumed:
large capacitance at V
tance at V
If the total capacitance at V
(< 0.01 F), relatively large external source resistances (up
to 80k for 20pF parasitic capacitance) can be tolerated
without any offset/full-scale error. Figures 19 and 20 show
a family of offset and full-scale error curves for various
small valued input capacitors (C
of input source resistance.
TUE
0
SOURCE
SIGNAL
INTPUT
IN
(C
Figure 17. Offset/Full-Scale Shift
Figure 18. An RC Network at V
IN
IN
< 0.01 F).
R
)
SOURCE
IN
(C
IN
V
REF
V
C
IN
IN
> 0.01 F) and small capaci-
IN
/2
(see Figure 18) is small
IN
< 0.01 F) as a function
C
PAR
20pF
IN
LTC2420
V
LTC2420
IN
IN
2420 F18
2420 F17
V
and V
REF
23
REF