LTC2393CUK-16#TRPBF Linear Technology, LTC2393CUK-16#TRPBF Datasheet - Page 14

• Manufacturer Part Number: LTC2393CUK-16#TRPBF
• Description: IC ADC 16BIT SER/PAR 1M 48-QFN
• Manufacturer: Linear Technology

Specifications of LTC2393CUK-16#TRPBF

• Number Of Bits: 16
• Sampling Rate (per Second): 1M
• Data Interface: Serial, Parallel
• Number Of Converters: 1
• Power Dissipation (max): 175mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 48-WFQFN, Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

LTC2393-16
APPLICATIONS INFORMATION
Signal-to-Noise Ratio (SNR)
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the first five harmonics and DC. Figure 5 shows
that the LTC2393-16 achieves a typical SNR of 94.2dB at
a 1MHz sampling rate with a 20kHz input.
Total Harmonic Distortion (THD)
Total harmonic distortion (THD) is the ratio of the RMS sum
of all harmonics of the input signal to the fundamental itself.
The out-of-band harmonics alias into the frequency band
between DC and half the sampling frequency (f
THD is expressed as:
where V
quency and V
through Nth harmonics.
POWER CONSIDERATIONS
The LTC2393-16 provides three sets of power supply
pins: the analog 5V power supply (AVP), the digital 5V
power supply (DVP) and the digital input/output interface
power supply (OVP). The flexible OVP supply allows the
LTC2393-16 to communicate with any digital logic operating
between 1.8V and 5V, including 2.5V and 3.3V systems.
14
THD
=
1
20
is the RMS amplitude of the fundamental fre-
2
log
through V
V
2
2
CNVST
+
BUSY
N
NAP
V
are the amplitudes of the second
3
2
V
1
+
V
4
2
t
5
...
V
N
Figure 6. Nap Mode Timing for the LTC2393-16
2
t
CONV
SMPL
/2).
NAP MODE
Power Supply Sequencing
The LTC2393-16 does not have any specific power sup-
ply sequencing requirements. Care should be taken to
observe the maximum voltage relationships described in
the Absolute Maximum Ratings section. The LTC2393-16
has a power-on-reset (POR) circuit. With the POR, the
result of the first conversion is valid after power has
been applied to the ADC. The LTC2393-16 will reset itself
if the power supply voltage drops below 2.5V. Once the
supply voltage is brought back to its nominal value, the
POR will reinitialize the ADC and it will be ready to start
a new conversion.
Nap Mode
The LTC2393-16 can be put into the nap mode after a
conversion has been completed to reduce the power
consumption between conversions. In this mode some
of the circuitry on the device is turned off. Nap mode is
enabled by keeping CNVST low between conversions. When
the next conversion is requested, bring CNVST high and
hold for at least 250ns, then start the next conversion by
bringing CNVST low. See Figure 6.
Power Shutdown Mode
When PD is tied high, the LTC2393-16 enters power shut-
down and subsequent requests for conversion are ignored.
Before entering power shutdown, the digital output data
needs to be read. However, if a request for power shutdown
(PD = high) occurs during a conversion, the conversion
t
ACQ
239316 F06
239316f