AD7323BRUZ Analog Devices Inc, AD7323BRUZ Datasheet - Page 15

• Manufacturer Part Number: AD7323BRUZ
• Description: IC ADC 12BIT+ SAR 4CHAN 16TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD7323BRUZ

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Bits: 12
• Sampling Rate (per Second): 500k
• Number Of Converters: 1
• Power Dissipation (max): 17mW
• Voltage Supply Source: Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP (0.173", 4.40mm Width)
• Resolution (bits): 13bit
• Sampling Rate: 500kSPS
• Input Channel Type: Pseudo Differential, Single Ended
• Supply Current: 900µA
• Digital Ic Case Style: TSSOP
• No. Of Pins: 16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7323CBZ - BOARD EVALUATION FOR AD7323CBZ
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of
crosstalk between any two channels. It is measured by applying a
full-scale, 100 kHz sine wave signal to all unselected input channels
and determining the degree to which the signal attenuates in the
selected channel with a 50 kHz signal. Figure 14 shows the worst-
case across all eight channels for the AD7323. The analog input
range is programmed to be the same on all channels.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion
products at sum and difference frequencies of mfa ± nfb, where
m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms
are those for which neither m nor n are equal to 0. For example,
the second-order terms include (fa + fb) and (fa − fb), whereas
the third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb),
and (fa − 2fb).
The AD7323 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second-order terms are usually distanced in
frequency from the original sine waves, whereas the third-order
Rev. A | Page 15 of 36
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
per the THD specification, where it is the ratio of the rms sum
of the individual distortion products to the rms amplitude of
the sum of the fundamentals, expressed in decibels.
PSR (Power Supply Rejection)
Variations in power supply affect the full-scale transition but
not the linearity of the converter. Power supply rejection is the
maximum change in the full-scale transition point due to a
change in power supply voltage from the nominal value (see the
Typical Performance Characteristics section).
CMRR (Common-Mode Rejection Ratio)
CMRR is defined as the ratio of the power in the ADC output at
full-scale frequency, f, to the power of a 100 mV sine wave
applied to the common-mode voltage of the V
frequency, f
where Pf is the power at frequency f in the ADC output, and Pf
is the power at frequency f
CMRR (dB) = 10 log (Pf/Pf
S
, as
S
in the ADC output (see Figure 17).
S
)
IN
+ and V
AD7323
IN
−
S