6-353293-8 TE Connectivity, 6-353293-8 Datasheet
6-353293-8
Specifications of 6-353293-8
Related parts for 6-353293-8
6-353293-8 Summary of contents
Page 1
... AMP Specifications: A. 109-5000 : Test Specification, General Requirements for Test Methods B. 114-5223 : Apprication Specification C. 501-5269 : Test Report 2.2 Commercial Standards and specifications : A. MIL-STD-202 : Test Methods for Electronic and Electrical Component Parts. B. IEC : International Electrotechnical Commission G ...
Page 2
... Single Row,Double Row Post Header Assembly Rellay Panel Mount Type. Post : Pre tin-Lead plated Brass (0.8µm min .thick tin-lead plating over0.5µm min.thick copper underplating) Housing : 66 Nylon NON G.F.(UL94V-O) F. Holder Housing for Double Row Housing : 66 Nylon NON G.F.(UL94V-O) Tyco Electronics AMP Shanghai Ltd ...
Page 3
... Applicable Panel Thickness 0.8~ 1.6mm (To be used for post header assembly relay) 3.7 Performance Requirements and Test Descriptions : The product shall be designed to meet the electrical, mechanical and environmental performance requirements specified in Fig ...
Page 4
... AMP Specification 114-5223. Electrical Requirements 10 mΩMax. (Initial) 20 mΩMax. (Final) No creeping discharge nor flashover shall occur. Current leakage : 5 Ma Max. 500 MΩMin. (Initial) 100 MΩMin. (Final) 30 °C Max. under loaded rating current. Fig. 2 (To be continued) PAGE Document No. 108-5525 Procedures ...
Page 5
... N(1.0 kgf) Min. 4.9 N(0.5 kgf) Min. 49 N(5 kgf ) MAX. 83.3 N(8.5 kgf) Min. See Fig.12 20 mΩ Max. (Final) Fig. 2 (To be continued) PAGE Document No Procedures Apply a pull-off load to terminated wire of contact secured on the tester, Operation Speed : 50 mm/min. ...
Page 6
... Solderability Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Requirements No electrical discontinuity greater than 1 µsec. Shall occur. 20 mΩ Max. (Final) No electrical discontinuity greater than 1µsec. Shall occur. 20 mΩ Max.(Final) No electrical discontinuity greater than 1µsec.shall occur. 20 mΩ Max.(Final) Wet Solder Coverage : 90 % Min ...
Page 7
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Requirements No physical damege shall Flow Soldering occur. Test connector on PCB. Solder Temerature : 260 ± 5 °C Immersion Duration : 10 ± 1 sec. Reflow Soldering Reflow Soldering by next conditions. Preheat:100~ 150℃ 60sec. Min. Heating:210 Peak Temperature:240 ...
Page 8
... IEC 68-2-1 20 mΩ Max. (Final) Mated connector SO2 Gas : 10 ± 3 ppm R.H. 35 ± 2 °C, 240 hours 20 mΩ Max. (Final) Mated connector H2S Gas : 3 ppm,40 ± 3 ℃ R.H.、 240 hours 20 mΩ Max. (Final) After 72 hours exposure in ...
Page 9
... Numbers indicate sequence in which the tests are performed. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Test Group Test Sequence (a) 1,6 1,3 1,3 1,3 1,3 1,3 1,3 1,3 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2 Fig.3 (To be continued) PAGE Document No. ...
Page 10
Test Examination Examination of Product Termination Resistance (Low Level) Dielectric withstanding Voltage Insulation Resistance Temperature Rising Crimp Tensile Strength Post Retention Force Contact Retention Force Panel Mounting Force Panel Retention Force Connector Mating/Unmating Force Durability (Repeated Mate/Unmating) Vibration (Low Frequency) ...
Page 11
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 4 Fig. 5 Fig. 6 PAGE Document No. 108-5525 REV LOC A ES ...
Page 12
Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 7 Fig. 8 PAGE Document No. 108-5525 REV LOC A ES ...
Page 13
Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 10 PAGE Document No. 108-5525 REV LOC A ES ...
Page 14
Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 11 PAGE Document No. 108-5525 REV LOC A ES ...
Page 15
... Note : To be applied same specification to post header relay panel mount type by measurement on opposite lock side. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Unmating Force N (kgf) min. 2.99 ) 4.508 ( 0.46 3.26 ) 5.194 ( 0 ...
Page 16
... SMT Type Without Boss 3~ 20 Pos. Emboss Tape Packaged for Single Row Post Header Assembly (V) SMT Type Without Boss 3~ 20 Pos. Single Row Post Header Assembly (H) DIP Staggered Type With Kink 2~ 20 Pos Fig. 1(To be continued) PAGE Document No. REV 108-5525 LOC A ES ...
Page 17
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Description Single Row Post Header Assembly Panel Mount Type 2~ 20 Pos. ...