AD7671AST Analog Devices Inc, AD7671AST Datasheet - Page 5

• Manufacturer Part Number: AD7671AST
• Description: IC ADC 16BIT CMOS 1MSPS 48-LQFP
• Manufacturer: Analog Devices Inc
• Series: PulSAR®r

Specifications of AD7671AST

• Rohs Status: RoHS non-compliant
• Number Of Bits: 16
• Sampling Rate (per Second): 1M
• Data Interface: Serial, Parallel
• Number Of Converters: 1
• Power Dissipation (max): 125mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• For Use With: EVAL-AD7671CBZ - BOARD EVALUATION FOR AD7671

REV. B
ABSOLUTE MAXIMUM RATINGS
Analog Inputs
Ground Voltage Differences
Supply Voltages
Internal Power Dissipation
Internal Power Dissipation
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150∞C
Storage Temperature Range . . . . . . . . . . . . –65∞C to +150∞C
Lead Temperature Range
NOTES
1
2
3
4
Model
AD7671AST
AD7671ASTRL
AD7671ACP
AD7671ACPRL
EVAL-AD7671CB
EVAL-CONTROL BRD2
NOTES
1
2
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD7671 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
Stresses above those listed under Absolute Maximum Ratings may cause permanent
damage to the device. This is a stress rating only; functional operation of the device
at these or any other conditions above those indicated in the operational section of
this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
This board can be used as a standalone evaluation board or in conjunction with the EVAL-CONTROL BRD2 for evaluation/demonstration purposes.
This board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators.
See Analog Inputs section.
Specification is for device in free air: 48-Lead LQFP: q
Specification is for device in free air: 48-Lead LFCSP: q
IND
INA, REF, INGND, REFGND, AGND
AGND, DGND, OGND . . . . . . . . . . . . . . . . . . . . . . ± 0.3 V
AVDD, DVDD, OVDD . . . . . . . . . . . . . . . . . –0.3 V to +7 V
AVDD to DVDD, AVDD to OVDD . . . . . . . . . . . . . . ± 7 V
DVDD to OVDD . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Digital Inputs . . . . . . . . . . . . . . . . –0.3 V to DVDD + 0.3 V
(Soldering 10 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . 300∞C
. . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to AVDD + 0.3 V
Figure 1. Load Circuit for Digital Interface Timing,
SDOUT, SYNC, SCLK Outputs, C
2
, INC
TO OUTPUT
*
IN SERIAL INTERFACE MODES, THE SYNC, SCLK, AND
SDOUT TIMINGS ARE DEFINED WITH A MAXIMUM LOAD
C
L
2
OF 10pF; OTHERWISE, THE LOAD IS 60pF MAXIMUM.
, INB
PIN
1
2
. . . . . . . . . . . . . . . . . . . . –11 V to +30 V
60pF
C
2
3
4
L
*
500 A
1.6mA
. . . . . . . . . . . . . . . . . . . . 700 mW
. . . . . . . . . . . . . . . . . . . . . . 2.5 W
1
I
I
OH
OL
Temperature Range
–40∞C to +85∞C
–40∞C to +85∞C
–40∞C to +85∞C
–40∞C to +85∞C
L
= 10 pF
JA
JA
= 91∞C/W, q
= 26∞C/W.
1.4V
JC
= 30∞C/W.
ORDERING GUIDE
–5–
NC = NO CONNECT
D2/DIVSCLK[0]
D3/DIVSCLK[1]
Package Description
Quad Flatpack (LQFP)
Quad Flatpack (LQFP)
Chip Scale (LFCSP)
Chip Scale (LFCSP)
Evaluation Board
Controller Board
Figure 2. Voltage Reference Levels for Timing
BYTESWAP
IMPULSE
SER/PAR
OB/2C
WARP
AGND
AVDD
t
DELAY
0.8V
NC
D0
D1
10
11
12
1
2
3
4
5
6
7
8
9
PIN CONFIGURATION
13 14 15 16 17 18 19 20 21 22 23 24
48 47 46 45 44
ST-48 and CP-48
PIN 1
IDENTIFIER
2V
0.8V
(Not to Scale)
TOP VIEW
AD7671
43 42 41 40
2V
39 38 37
t
Package Option
ST-48
ST-48
CP-48
CP-48
DELAY
2V
0.8V
AD7671
36
35
34
33
32
31
30
29
28
27
26
25
AGND
CNVST
PD
RESET
CS
RD
DGND
BUSY
D15
D14
D13
D12