ADC0816CJ National Semiconductor, ADC0816CJ Datasheet - Page 5

• Manufacturer Part Number: ADC0816CJ
• Description: IC ADC 8BIT W/16CH MUX 40-DIP
• Manufacturer: National Semiconductor

Specifications of ADC0816CJ

• Number Of Bits: 8
• Sampling Rate (per Second): 10k
• Data Interface: Parallel
• Number Of Converters: 1
• Power Dissipation (max): 875mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: *ADC0816CJ

Functional Description
Multiplexer: The device contains a 16-channel single-ended
analog signal multiplexer. A particular input channel is se-
lected by using the address decoder. Table *NO TGT: table
NS0669* shows the input states for the address line and the
expansion control line to select any channel. The address is
latched into the decoder on the low-to-high transition of the
address latch enable signal.
X = don’t care
Selected
Analog Channel
All Channels OFF
IN10
IN11
IN12
IN13
IN14
IN15
IN0
IN1
IN2
IN3
IN4
IN5
IN6
IN7
IN8
IN9
D
H
H
H
H
H
H
H
H
X
L
L
L
L
L
L
L
L
Address Line
C
H
H
H
H
H
H
H
H
L
L
L
L
L
L
L
L
X
B
H
H
H
H
H
H
H
H
X
L
L
L
L
L
L
L
L
FIGURE 1. Resistor Ladder and Switch Tree
A
H
H
H
H
H
H
H
H
X
L
L
L
L
L
L
L
L
Expansion
Control
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
5
Additional single-ended analog signals can be multiplexed to
the A/D converter by disabling all the multiplexer inputs using
the expansion control. The additional external signals are
connected to the comparator input and the device ground.
Additional signal conditioning (i.e., prescaling, sample and
hold, instrumentation amplification, etc.) may also be added
between the analog input signal and the comparator input.
CONVERTER CHARACTERISTICS
The Converter
The heart of this single chip data acquisition system is its
8-bit analog-to-digital converter. The converter is designed to
give fast, accurate, and repeatable conversions over a wide
range of temperatures. The converter is partitioned into 3
major sections: the 256R ladder network, the successive ap-
proximation register, and the comparator. The converter’s
digital outputs are positive true.
The 256R ladder network approach Figure 1 was chosen
over the conventional R/2R ladder because of its inherent
monotonicity, which guarantees no missing digital codes.
Monotonicity is particularly important in closed loop feedback
control systems. A non-monotonic relationship can cause os-
cillations that will be catastrophic for the system. Additionally,
the 256R network does not cause load variations on the ref-
erence voltage.
The bottom resistor and the top resistor of the ladder net-
work in Figure 1 are not the same value as the remainder of
the network. The difference in these resistors causes the
output characteristic to be symmetrical with the zero and
full-scale points of the transfer curve. The first output transi-
tion occurs when the analog signal has reached +
and succeeding output transitions occur every 1 LSB later up
to full-scale.
DS005277-2
www.national.com
1
⁄
2
LSB