AD7879-1ACPZ-RL Analog Devices Inc, AD7879-1ACPZ-RL Datasheet - Page 33
![IC ADC 12BIT CTLR TOUCH 16LFCSP](/photos/6/50/65061/505-16-lfcsp_sml.jpg)
AD7879-1ACPZ-RL
Manufacturer Part Number
AD7879-1ACPZ-RL
Description
IC ADC 12BIT CTLR TOUCH 16LFCSP
Manufacturer
Analog Devices Inc
Type
Resistiver
Specifications of AD7879-1ACPZ-RL
Resolution (bits)
12 b
Data Interface
I²C, Serial
Touch Panel Interface
4-Wire
Number Of Inputs/keys
1 TSC
Data Rate/sampling Rate (sps, Bps)
105k
Voltage Reference
External
Voltage - Supply
1.6 V ~ 3.6 V
Current - Supply
10nA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-LFCSP
Voltage Supply Source
Single Supply
Sampling Rate (per Second)
105k
Sampling Rate
105kSPS
Supply Voltage Range - Analog
1.6V To 3.6V
Supply Current
480µA
Digital Ic Case Style
CSP
No. Of Pins
16
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
SCL
Reading Data
A read transaction begins when the master writes the command
word to the AD7879/AD7889 with the read/write bit set to 1. The
master then supplies 16 clock pulses per data-word to be read,
and the AD7879/AD7889 clock out data from the addressed
register on the DOUT line. The first data-word is clocked out
on the first falling edge of SCL following the command word,
as shown in Figure 41.
DIN
CS
NOTES
1. MULTIPLE SEQUENTIAL REGISTERS CAN BE LOADED CONTINUOUSLY.
2. THE FIRST (LOWEST ADDRESS) REGISTER ADDRESS IS WRITTEN, FOLLOWED BY MULTIPLE 16-BIT DATA-WORDS.
3. THE ADDRESS AUTOMATICALLY INCREMENTS WITH EACH 16-BIT DATA-WORD (ALL 16 BITS MUST BE WRITTEN).
4. CS IS HELD LOW UNTIL THE LAST DESIRED REGISTER HAS BEEN LOADED.
5. 16-BIT COMMAND WORD SETTINGS FOR SEQUENTIAL WRITE OPERATION:
CW
CW[15:11] = 11100 (ENABLE WORD)
CW[10] = 0 (R/W)
CW[9:0] = [AD9, AD8, AD7, AD6, AD5, AD4, AD3, AD2, AD1, AD0] (STARTING MSB JUSTIFIED REGISTER ADDRESS)
15
DOUT
1
SCL
DIN
CS
ENABLE WORD
CW
14
2
CW
13
NOTES
1. DATA BITS ARE LATCHED ON SCL RISING EDGES. SCL CAN IDLE HIGH OR LOW BETWEEN WRITE OPERATIONS.
2. THE 16-BIT COMMAND WORD MUST BE WRITTEN ON DIN: 5 BITS FOR ENABLE WORD, 1 BIT FOR R/W, AND 10 BITS FOR REGISTER ADDRESS.
3. THE REGISTER DATA IS READ BACK ON THE DOUT PIN.
4. X DENOTES DON’T CARE.
5. XXX DENOTES HIGH IMPEDANCE THREE-STATE OUTPUT.
6. CS IS HELD LOW UNTIL ALL REGISTER BITS HAVE BEEN READ BACK.
7. 16-BIT COMMAND WORD SETTINGS FOR SINGLE READBACK OPERATION:
3
CW[15:11] = 11100 (ENABLE WORD)
CW[10] = 1 (R/W)
CW[9:0] = [AD9, AD8, AD7, AD6, AD5, AD4, AD3, AD2, AD1, AD0] (10-BIT MSB JUSTIFIED REGISTER ADDRESS)
CW
XXX
15
t
CW
2
12
1
t
1
4
ENABLE WORD
XXX
CW
14
CW
11
2
5
t
3
XXX
CW
13
R/W
CW
10
3
16-BIT COMMAND WORD
6
XXX
CW
12
CW
4
9
7
XXX
CW
11
CW
5
8
8
R/W
CW
XXX
t
10
4
STARTING REGISTER ADDRESS
CW
6
7
16-BIT COMMAND WORD
9
XXX
CW
9
CW
7
6
10
XXX
CW
Figure 40. Sequential Register Write, SPI Timing
Figure 41. Single Register Readback, SPI Timing
8
CW
8
5
11
CW
XXX
7
t
CW
5
9
4
12
REGISTER ADDRESS
XXX
CW
6
10
CW
3
Rev. C | Page 33 of 40
13
XXX
CW
5
11
CW
2
14
CW
XXX
4
12
CW
1
15
CW
XXX
3
13
CW
0
16
The AD7879/AD7889 continue to clock out data on the DOUT
line provided that the master continues to supply the clock signal
on SCL. The read transaction ends when the master takes CS high.
If the AD7879/AD7889 address pointer reaches its maximum
value, the AD7879/AD7889 repeatedly clock out data from the
addressed register. The address pointer does not wrap.
XXX
CW
2
14
D15
17
XXX
CW
1
15
DATA FOR STARTING
REGISTER ADDRESS
D14
18
XXX
CW
0
16
D15
X
17
t
6
D14
X
18
16-BIT READBACK DATA
D1
31
D13
X
19
D0
32
D15
33
D14
REGISTER ADDRESS
34
DATA FOR NEXT
D2
X
30
AD7879/AD7889
D1
X
t
8
31
t
7
D0
X
32
D1
47
XXX
D0
48
D15
49