MAX5428EUA+ Maxim Integrated Products, MAX5428EUA+ Datasheet - Page 5

• Manufacturer Part Number: MAX5428EUA+
• Description: IC POT DGTL 1TIME PROGR 8-UMAX
• Manufacturer: Maxim Integrated Products

Specifications of MAX5428EUA+

• Taps: 32
• Resistance (ohms): 50K
• Number Of Circuits: 1
• Temperature Coefficient: 35 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Resistance In Ohms: 50K
• Number Of Pots: Single
• Taps Per Pot: 32
• Resistance: 50 KOhms
• Wiper Memory: Non Volatile
• Digital Interface: Serial (2-Wire)
• Operating Supply Voltage: 5 V
• Supply Current: 1.5 uA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

(V
The MAX5427/MAX5428/MAX5429 are 100k /50k /
10k
tiometers. They have 32 tap positions that are accessible
to the wiper along the resistor array between H and L.
The wiper (W) position is adjusted sequentially through
the tap positions using a simple 2-wire interface. These
digital potentiometers have an optional one-time pro-
grammable feature that sets the POR position of the
wiper. The 2-wire interface can then be disabled, perma-
nently preventing unwanted adjustment.
The MAX5427/MAX5428/MAX5429 have two modes of
operation when the serial interface is active: increment
DD
-0.02
-0.04
-0.06
-0.08
-0.10
0.10
0.08
0.06
0.04
0.02
PIN
= 5.0V, T
0
1
2
3
4
5
6
7
8
(end-to-end resistance) digitally controlled poten-
0
R-INL ERROR vs. INPUT CODE
5
A
= +25°C, unless otherwise noted.)
INPUT CODE (DECIMAL)
10
NAME
GND
(MAX5428)
V
U/D
V
CS
_______________________________________________________________________________________
W
DD
H
L
PP
15
Digital Interface Operation
One-Time Programmable, Linear-Taper
Detailed Description
20
Wiper Connection
Chip-Select Input. A high-to-low CS transition determines the mode: increment if U/D is high, or
decrement if U/D is low. CS is also used for one-time programming (see the One-Time Programming
section).
Power-Supply Voltage
Ground
Programming Voltage for One-Time Programming. Connect V
programming the device. For normal operation, connect to ground or let float.
Up/Down Control Input. With CS low, a low-to-high transition increments or decrements the wiper
position.
Low Terminal of Resistor
High Terminal of Resistor
25
30
-0.005
-0.010
-0.015
-0.020
-0.025
0.025
0.020
0.015
0.010
0.005
Typical Operating Characteristics (continued)
0
0
R-DNL ERROR vs. INPUT CODE
5
INPUT CODE (DECIMAL)
10
(MAX5429)
15
mode and decrement mode. The serial interface is only
active when CS is low.
The CS and U/D inputs control the position of the wiper
along the resistor array. When CS transitions from high
to low, the part goes into increment mode if U/D is high
(Figure 2), and into decrement mode if U/D is low
(Figure 3). Once the mode is set, the device remains in
that mode until CS goes high. A low-to-high transition at
the U/D increments or decrements the wiper position
depending on the current mode.
When the CS input transitions to high (when serial inter-
face is inactive) and U/D is low, the wiper increments or
decrements one position in accordance with the state
of U/D when CS went low. If U/D is high when CS tran-
sitions to high, the wiper remains in the same position.
Digital Potentiometers
20
FUNCTION
25
30
PP
-0.02
-0.04
-0.06
-0.08
-0.10
0.10
0.08
0.06
0.04
0.02
to 10V supply when one-time
0
0
R-INL ERROR vs. INPUT CODE
5
Pin Description
INPUT CODE (DECIMAL)
10
(MAX5429)
15
20
25
30
5