MCP4021T-103E/MS Microchip Technology, MCP4021T-103E/MS Datasheet - Page 30
![IC DGTL POT 10K 1CH 8MSOP](/photos/6/59/65932/mfg_150_c04-111_ms_8-msop_sml.jpg)
MCP4021T-103E/MS
Manufacturer Part Number
MCP4021T-103E/MS
Description
IC DGTL POT 10K 1CH 8MSOP
Manufacturer
Microchip Technology
Specifications of MCP4021T-103E/MS
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Taps
64
Resistance (ohms)
10K
Number Of Circuits
1
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Non-Volatile
Interface
Up/Down
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Resistance In Ohms
10K
Number Of Pots
Single
Taps Per Pot
64
Resistance
10 KOhms
Wiper Memory
Non Volatile
Digital Interface
Serial (2-Wire)
Operating Supply Voltage
3.3 V, 5 V
Supply Current
45 uA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MCP4XXXDM-DB - BOARD DAUGHTER DIGIPOT MCP4XXXMCP402XEV - BOARD EVAL FOR MCP402X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCP4021T-103E/MS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
MCP4021/2/3/4
5.2.1
This mode is achieved by initializing the U/D pin to a
high state (V
CS pin. Subsequent rising edges of the U/D pin
increment the wiper setting toward terminal A. This is
shown in
After the wiper is incremented to the desired position,
the CS pin should be forced to V
“unexpected” transitions (on the U/D pin do not cause
the wiper setting to increment. Driving the CS pin to V
should occur as soon as possible (within device
specifications) after the last desired increment occurs.
FIGURE 5-1:
DS21945E-page 30
WiperLock™ Technology
Figure
INCREMENT WITHOUT WRITING
WIPER SETTING TO EEPROM
IH
) prior to achieving a low state (V
5-1.
EEPROM
Increment without Writing Wiper Setting to EEPROM.
Wiper
U/D
CS
Note: If WiperLock technology enabled, wiper will not move.
IH
to ensure that
V
V
IL
IL
X
X
IL
1
) on the
X+1
X
IH
2
X+2
X
3
The EEPROM value has not been updated to this new
wiper value, so if the device voltage is lowered below
the RAM retention voltage of the device, once the
device returns to the operating range, the wiper will be
loaded with the wiper setting in the EEPROM.
After the CS pin is driven to V
serial command may immediately be entered. This is
since an EEPROM write cycle (t
X+3
X
Note:
4
X+4
X
The wiper value will not overflow. That is,
once the wiper value equals 0x3F,
subsequent increment commands are
ignored.
WiperLock Technology Enable
WiperLock Technology Disable
© 2006 Microchip Technology Inc.
5
IH
6
wc
(from V
) is not active.
V
V
IH
IH
IL
), any other