ISL97682IRTZ-T Intersil, ISL97682IRTZ-T Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL97682IRTZ-T
Manufacturer Part Number
ISL97682IRTZ-T
Description
2 Channel LED Driver, 16LD TQFN 3X3, T&R
Manufacturer
Intersil
Series
-r
Datasheet
1.ISL97682IRTZ.pdf
(17 pages)
Specifications of ISL97682IRTZ-T
Constant Current
-
Constant Voltage
-
Topology
PWM, Step-Up (Boost)
Number Of Outputs
2
Internal Driver
Yes
Type - Primary
Backlight
Type - Secondary
-
Frequency
500kHz ~ 650kHz, 900kHz ~ 1.1MHz
Voltage - Supply
4 V ~ 26.5 V
Voltage - Output
45V
Mounting Type
Surface Mount
Package / Case
16-WFQFN Exposed Pad
Operating Temperature
-40°C ~ 85°C
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL97682IRTZ-TK
Manufacturer:
INTERSIL
Quantity:
20 000
Theory of Operation
PWM Boost Converter
The current mode PWM boost converter produces the minimal
voltage needed to enable the LED stack with the highest forward
voltage drop to run at the programmed current. The ISL97682,
ISL97683, ISL97684 employs current mode control boost
architecture that has a fast current sense loop and a slow voltage
feedback loop. Such architecture achieves a fast transient
response that is essential for the notebook backlight application
where the power can be a series of drained batteries or instantly
change to an AC/DC adapter without rendering a noticeable
visual nuisance. The number of LEDs that can be driven by the
ISL97682, ISL97683, ISL97684 depend on the type of LED
chosen in the application. The ISL97682, ISL97683, ISL97684
are capable of boosting up to 45V and typically driving 13 LEDs
in series for each of the 4 channels, enabling a total of 52 pieces
of the 3.2V/20mA type of LEDs.
OVP
The Overvoltage Protection (OVP) pin has a function of setting the
overvoltage trip level as well as limiting the V
range.
The ISL97682, ISL97683, ISL97684 OVP threshold is set by
R
V
such that:
Allowable V
For example, if 10 LEDs are used with the worst case being V
of 35V. If R
40V, then the V
If the requirement is changed to 4 LEDs of 14V V
then the OVP level must be reduced and users should follow the
V
headroom control will be disturbed such that the channel voltage
can be much higher than expected and sometimes can prevent
the driver from operating properly.
The ratio of the OVP capacitor should be the inverse of the OVP
resistor. For example:
if R
C
Enable
An EN signal is required to enable the internal regulator for normal
operation. If there is no signal for longer than 28ms, the device will
enter shutdown.
Power Sequence
There is no specific power sequence requirement for the
ISL97682, ISL97683, ISL97684. The EN signal can be tied to V
but not the VDC that will prevent the device from powering up.
V
OUT
OUT
UPPER
UPPER
OUT_OVP
UPPER
can only regulate between 42% and 100% of the V
= (42% ~100%) OVP level requirement. Otherwise, the
= 100pF and C
and R
/R
= 1.22V * (R
1
OUT
LOWER
and R
LOWER
OUT
= 42% to 100% of V
2
is allowed to operate between 16.8V and 40V.
= 33/1, then C
are chosen such that the OVP level is set at
shown by Equation 1:
UPPER
UPPER
+ R
= 3.3nF.
10
LOWER
UPPER
OUT_OVP
ISL97682, ISL97683, ISL97684
)/R
/C
LOWER
LOWER
OUT
OUT
regulation
= 1/33 with
application,
OUT_OVP
(EQ. 1)
OUT
IN
Current Matching and Current Accuracy
Each channel of the LED current is regulated by the current
source circuit, as shown in Figure 19.
The LED peak current is set by translating the R
output with a scaling factor of 401.8/R
of the current source MOSFETs are designed to run at 500mV to
optimize power loss versus accuracy requirements. The sources
of errors of the channel-to-channel current matching come from
the op amps offset, internal layout, reference, and current source
resistors. These parameters are optimized for current matching
and absolute current accuracy. However, the absolute accuracy is
additionally determined by the external R
resistor is recommended.
Dynamic Headroom Control
The ISL97682, ISL97683, ISL97684 feature a proprietary
Dynamic Headroom Control circuit that detects the highest
forward voltage string or the lowest voltage from any of the CH
pins digitally. When the lowest CH voltage is lower than the short
circuit threshold (V
signal for the boost regulator. The boost makes the output to the
correct level such that the lowest CH is at the target headroom
voltage. Since all LED stacks are connected to the same output
voltage, the other CH pins will have a higher voltage, but the
regulated current source circuit on each channel will ensure that
each channel has the same current. The output voltage will
regulate cycle-by-cycle and it is always referenced to the highest
forward voltage string in the architecture.
Dimming Controls
The ISL97682, ISL97683, ISL97684 allow two ways of controlling
the LED current, and therefore, the brightness. They are:
There are various ways to achieve DC or PWM current control,
which will be described in the following.
1. DC current adjustment
2. PWM chopping of the LED current defined in Step 1.
FIGURE 19. SIMPLIFIED CURRENT SOURCE CIRCUIT
PWM DIMMING
RSET
SC
), such voltage will be used as the feedback
+
-
REF
+
-
SET
SET
. The source terminals
. A 1% tolerance
SET
current to the
March 11, 2011
FN7689.0