X9421WS16-2.7T1 Intersil, X9421WS16-2.7T1 Datasheet
![IC XDCP SGL 64-TAP 10K 16-SOIC](/photos/5/65/56533/20-16-soic_sml.jpg)
X9421WS16-2.7T1
Specifications of X9421WS16-2.7T1
Related parts for X9421WS16-2.7T1
X9421WS16-2.7T1 Summary of contents
Page 1
... SS CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 XDCP is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005, 2008, 2009. All Rights Reserved All other trademarks mentioned are the property of their respective owners. X9421 Low Noise/Low Power/SPI Bus FN8196 ...
Page 2
... X9421 YVG X9421YV14IZ-2.7* (Pb-free) X9421 YVZG X9421WS16-2.7* X9421WS F X9421WS16Z-2.7* (Note) X9421WS ZF X9421WS16I-2.7* X9421WS G X9421WS16IZ-2.7* (Note) X9421WS ZG X9421WV14-2.7* X9421 WVF X9421WV14Z-2.7* (Pb-free) X9421 WVZF X9421WV14I-2.7* X9421 WVG X9421WV14IZ-2.7* (Pb-free) X9421 WVZG *Add "T1" suffix for tape and reel. Please refer to TB347 for details on reel specifications. ...
Page 3
Detailed Functional Diagrams V CC HOLD CONTROL CS INTERFACE SCK AND SO CONTROL CIRCUITRY Circuit Level Applications • Vary the Gain of a Voltage Amplifier • Provide Programmable DC Reference Voltages for Comparators and Detectors ...
Page 4
X9421 (14 LD TSSOP) TOP VIEW SCK SI 6 VSS 7 Pin Assignments TSSOP SOIC PIN NO. PIN NO ...
Page 5
DEVICE ADDRESS ( The address input is used to set the least significant bit of the 8-bit slave address. A match in the slave address serial data stream must be made with the address input in order to ...
Page 6
SERIAL DATA PATH FROM INTERFACE CIRCUITRY REGISTER 0 REGISTER 2 IF WCR = 00[H] THEN WCR = 3F[H] THEN FIGURE 1. DETAILED POTENTIOMETER BLOCK DIAGRAM Write In Process The ...
Page 7
Two of the eight instructions are two bytes in length and end with the transmission of the instruction byte. These instructions are: • XFR Data Register to Wiper Counter Register —This instruction transfers the contents of one specified Data Register ...
Page 8
CS SCL FIGURE 6. THREE-BYTE INSTRUCTION SEQUENCE (READ) CS SCK FIGURE 7. INCREMENT/DECREMENT INSTRUCTION SEQUENCE SCK INC/DEC CMD ISSUED 8 X9421 ...
Page 9
INSTRUCTION I 3 Read Wiper Counter Register 1 Write Wiper Counter Register 1 Read Data Register 1 Write Data Register 1 XFR Data Register to Wiper 1 Counter Register XFR Wiper Counter Register to Data 1 Register Increment/Decrement Wiper 0 ...
Page 10
Transfer Data Register (DR) to Wiper Counter Register (WCR) Transfer the contents of the Register pointed the WCR. DEVICE TYPE DEVICE CS IDENTIFIER ADDRESSES FALLING EDGE ...
Page 11
... Thermal Resistance (Typical, Note 1) 14 Lead TSSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Lead SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-Free Reflow Profile .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Temperature Range Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C Industrial .-40°C to +85°C TEST CONDITIONS +25° ...
Page 12
DC Electrical Specifications (Over the recommended operating conditions unless otherwise specified). SYMBOL PARAMETER I V Supply Current CC1 CC (Active Supply Current CC2 CC (Nonvolatile Write Current (Standby Input Leakage Current LI I ...
Page 13
AC Test Conditions I nput pulse levels V CC Input rise and fall times 10ns Input and output timing level V CC Equivalent AC Load Circuit 5V 1533Ω SDA Output 100pF Circuit #3 SPICE Macro Model R TOTAL R H ...
Page 14
AC Timing SYMBOL f SSI/SPI Clock Frequency SCK t SSI/SPI Clock Cycle Time CYC t SSI/SPI Clock High Time WH t SSI/SPI Clock Low Time WL t Lead Time LEAD t Lag Time LAG t SI, SCK, HOLD and CS ...
Page 15
Symbol Table WAVEFORM INPUTS OUTPUTS MUST BE WILL BE STEADY STEADY MAY CHANGE WILL CHANGE FROM LOW TO FROM HIGH HIGH MAY CHANGE WILL CHANGE FROM HIGH TO FROM HIGH TO LOW LOW DON’T CARE: CHANGING: CHANGES ...
Page 16
Hold Timing CS SCK HOLD XDCP Timing (for All Load Instructions) CS SCK MSB HIGH IMPEDANCE SO XDCP Timing (for Increment/Decrement Instruction) CS SCK ADDR HIGH IMPEDANCE SO 16 X9421 ...
Page 17
Write Protect and Device Address Pins Timing Applications information 1. Electronic potentiometers provide three powerful application advantages: The variability and reliability of a solid-state potentiometer, Basic Configurations of Electronic Potentiometers ...
Page 18
Application Circuits BUFFERED REFERENCE VOLTAGE +5V V OP- – -5V VOLTAGE REGULATOR V 317 adj (REG) = 1.25V (1 adj ...
Page 19
Thin Shrink Small Outline Plastic Packages (TSSOP) N INDEX 0.25(0.010) E AREA E1 - 0.05(0.002) SEATING PLANE - -C- α 0.10(0.004) 0.10(0.004 NOTES: 1. These package ...
Page 20
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...