MCP4728-E/UN Microchip Technology, MCP4728-E/UN Datasheet - Page 33

• Manufacturer Part Number: MCP4728-E/UN
• Description: IC DAC 12BIT W/I2C 10-MSOP
• Manufacturer: Microchip Technology

Specifications of MCP4728-E/UN

• Number Of Converters: 4
• Settling Time: 6µs
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Number Of Bits: 12
• Data Interface: I²C
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Number Of Dac Outputs: 4
• Resolution: 12 bit
• Interface Type: I2C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Supply Current: 110 mA
• Voltage Reference: 2.048 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP4728EV - BOARD EVAL 12BIT 4CH DAC MCP4728
• Power Dissipation (max): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

5.4.4
This command is used to read the I
the device. If the second byte is “00001100” (0Ch), the
device will output its address bits stored in EEPROM
and register. This command uses the LDAC pin to
FIGURE 5-6:
© 2010 Microchip Technology Inc.
Start
S 0 0 0 0 0 0 0 0 A 0 0 0 0 1 1 0 0 A Sr 1 1 0 0 X X X 1 A A2 A1 A0 1 A2 A1 A0 0 A P
Clock Pulse
(CLK Line)
Clock and LDAC Transition Details:
LDAC Pin
Note 1: Clock Pulse and LDAC Transition Details.
(General Call Address)
LDAC Pin
2nd Byte
2:
3: LDAC pin resumes its normal function after “Stop” bit.
GENERAL CALL READ ADDRESS
BITS
1st Byte
6
LDAC pin events at the 2nd and 3rd bytes.
a.
b.
c.
Note 2 (a)
7
Keep LDAC pin “High” until the end of the positive pulse of the 8th clock of the 2nd byte.
LDAC pin makes a transition from “High” to “Low” during the negative pulse of the 8th clock of the 2nd
byte (just before the rising edge of the 9th clock) and stays “Low” until the rising edge of clock 9 of the
3rd byte.
The MCP4728 device does not acknowledge the 3rd byte if the conditions (a) and (b) are not met.
General Call Read I
ACK Clock
8
9
Note 2(b, c)
2
Sr
2nd Byte
C address bits of
Restart Clock
Stay “Low” until the end of the 3rd Byte
1
2
C Address.
ACK (MCP4728)
2
3
Note 2(b)
Restart
4
(Notes 1, 2, 3)
3rd Byte
select the device of interest to read on the I
LDAC pin needs a logic transition from “High” to “Low”
during the negative pulse of the 8th clock of the second
byte, and stays “Low” until the end of the 3rd byte. The
maximum clock rate for this command is 400 kHz.
Restart Byte
5
3rd Byte
6
7
8
Address Bits
EEPROM
ACK Clock
9
Reading Address Bits
in
4th Byte
Note 3
1
MCP4728
Reading Address Bits
Note 3
Address Bits
4th Byte
2
Register
in Input
DS22187E-page 33
ACK (Master)
3
2
C bus. The
Stop