B6TS16LFDEFAULT Omron, B6TS16LFDEFAULT Datasheet
B6TS16LFDEFAULT
Specifications of B6TS16LFDEFAULT
Related parts for B6TS16LFDEFAULT
B6TS16LFDEFAULT Summary of contents
Page 1
... Capacitive Touch Sensing ICs - B6TS Text OMRON expands its switch product range by introducing the new touch sensor switch family B6TS which is based on a capacitive measurement principle: ■ B6TS-04LT – 4 channel sensor ■ B6TS-08LF – 8 channel sensor ■ B6TS-16LF – 16 channel sensor Features • ...
Page 2
Text Capacitive Touch Sensing ICs - B6TS B6TS-04LT - 4 Channel Sensor ■ Pin arrangement diagram Note 1: Pins TEST1, and TEST2 are used for testing during manufacture of the IC. When using these pins, connect them to VDD through ...
Page 3
Capacitive Touch Sensing ICs - B6TS Text Pin Desig- Input/ No. nation Output 19 ___ Output pin to indicate operation. OUT0 [Normal measurement mode] outputs measured results. CHG O [On/off output mode] channel 0 output (active low) [Serial communication mode] ...
Page 4
Text Capacitive Touch Sensing ICs - B6TS Absolute maximum ratings Designation Item V Supply voltage DD V Input voltage I V Output voltage O P Power dissipation d T Ambient operating temperature opr T Storage temperature stg Recommended operating conditions ...
Page 5
Text Capacitive Touch Sensing ICs - B6TS Pin functions Pin Desig- Input/ No. nation Output 11 CH0A I/O Connect these pins to the touch electrode through the measurement pins (channels CH1A 14 CH2A 16 CH3A 17 ...
Page 6
Text Capacitive Touch Sensing ICs - B6TS Electrical characteristics [V Designation Item — Number of times of EEPROM write — EEPROM write time — EEPROM data retention period Note 1: Unless otherwise specified, V Note 2: The period following receipt ...
Page 7
Capacitive Touch Sensing ICs - B6TS Text Connection Diagram (example) Note 1: Connect Rr, Cr, Rc, and Cc to each touch electrode, as shown in the above figure. Refer to the design tool (B6TWorkbench) for their actual values ...
Page 8
Text Capacitive Touch Sensing ICs - B6TS Absolute maximum ratings Designation Item V Supply voltage DD V Input voltage I V Output voltage O P Power dissipation d T Ambient operating temperature opr T Storage temperature stg Recommended operating conditions ...
Page 9
Capacitive Touch Sensing ICs - B6TS B6TS-16LF– 16 Channel Sensor ■ Pin arrangement diagram Note 1: Pins TEST is used for testing during manufacture of the IC. When using this IC, connect it to Vdd through a pull-up resistor. Pin ...
Page 10
Capacitive Touch Sensing ICs - B6TS Pin Desig- Input/ No. nation Output 13 CHG O An output pin which indicates the operation status. [Normal measurement mode] Outputs measurements results. [Serial communication mode] – Measurement termination output. Two output modes are ...
Page 11
Capacitive Touch Sensing ICs - B6TS Connection Diagram (example) Note 1: Connect Rr, Cr, Rc, and Cc to each touch electrode, as shown in the above figure. Refer to the design tool (B6TWWorkbench) for their actual values 10kΩ ...
Page 12
Capacitive Touch Sensing ICs - B6TS Absolute maximum ratings Designation Item V Supply voltage DD V Input voltage I V Output voltage O P Power dissipation d T Ambient operating temperature opr T Storage temperature stg Recommended operating conditions Designation ...
Page 13
... NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. ...