CC109130481 Lineage Power, CC109130481 Datasheet - Page 11

• Manufacturer Part Number: CC109130481
• Description: Module DC-DC 1-OUT 0.6V to 3.63V 12A 10-Pin SMT T/R
• Manufacturer: Lineage Power
• Type: Step Downr

Specifications of CC109130481

• Package: 10SMT
• Output Current: 12 A
• Output Voltage: 0.6 to 3.63 V
• Input Voltage: 12 V
• Number Of Outputs: 1
• Switching Regulator: Yes

Data Sheet
April 7, 2011
Test Configurations
Figure 31. Input Reflected Ripple Current Test
Setup.
Figure 32. Output Ripple and Noise Test Setup.
Figure 33. Output Voltage and Efficiency Test Setup.
LINEAGE
NOTE: All voltage measurements to be taken at the module
TO OSCILLOSCOPE
NOTE: Measure input reflected ripple current with a simulated
COM
Efficiency
Vo+
R
R
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
NOTE: All voltage measurements to be taken at the module
distribution
distribution
source inductance (L
possible battery impedance. Measure current as shown
above.
POWER
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
R
R
contact
contact
η =
@ 20°C 100kHz
COPPER STRIP
E.S.R.<0.1Ω
0.1uF
C
Electrolytic
S
1000μF
L
1μH
TEST
V
IN
V
V
V
COM
TEST
IN
IN
O
GROUND PLANE
(+)
. I
. I
) of 1μH. Capacitor C
O
IN
10uF
COM
V
O
Tantalum
2x100μF
V
C
2.4 – 5.5Vdc input; 0.6Vdc to 3.63Vdc output; 12A output current
x 100 %
O
IN
CURRENT PROBE
SCOPE USING
BNC SOCKET
R
R
contact
contact
S
offsets
V
COM
IN
(+)
R
R
RESISTIVE
LOAD
distribution
distribution
R
LOAD
Micro TLynx
Design Considerations
Input Filtering
The Micro TLynx
low ac-impedance source. A highly inductive source
can affect the stability of the module. An input
capacitance must be placed directly adjacent to the
input pin of the module, to minimize input ripple
voltage and ensure module stability.
To minimize input voltage ripple, low-ESR ceramic
capacitors are recommended at the input of the module.
Figure 34 shows the input ripple voltage for various
output voltages at 3A of load current with 1x47 µF or
2x47 µF ceramic capacitors and an input of 5V. Figure
35 shows data for the 3.3Vin case, with 1x47µF or
2x37µF of ceramic capacitors at the input.
Figure 34. Input ripple voltage for various output
voltages with 1x47 µF or 2x47 µF ceramic
capacitors at the input (12A load). Input voltage is
5V.
Figure 35. Input ripple voltage in mV, p-p for
various output voltages with 1x47 µF or 2x47 µF
ceramic capacitors at the input (12A load). Input
voltage is 3.3V.
TM
140
120
100
120
100
80
60
40
20
80
60
40
20
: Non-isolated DC-DC Power Modules:
0
0
0.5
0.5
1x47uF
2x47uF
TM
1x47uF
2x47uF
1
1
module should be connected to a
Output Voltage (Vdc)
Output Voltage (Vdc)
1.5
1.5
2
2
2.5
2.5
3
3.5
3
11