MAX5134AGUE+ Maxim Integrated Products, MAX5134AGUE+ Datasheet - Page 10

• Manufacturer Part Number: MAX5134AGUE+
• Description: IC DAC 16BIT QUAD 16-TSSOP
• Manufacturer: Maxim Integrated Products

Specifications of MAX5134AGUE+

• Settling Time: 5µs
• Number Of Bits: 16
• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Converters: 4
• Voltage Supply Source: Analog and Digital
• Power Dissipation (max): 457mW
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Pin-/Software-Compatible,
16-/12-Bit, Voltage-Output DACs
when using the internal reference. Bypass REFO to
GND with a 47pF (maximum 100pF) capacitor.
Alternatively, if heavier decoupling is required, use a
1kΩ resistor in series with a 1µF capacitor in parallel
with the existing 100pF capacitor. REFO can deliver up
to 100µA of current with no degradation in perfor-
mance. Configure other reference voltages by applying
a resistive potential divider with a total resistance
greater than 33kΩ from REFO to GND.
The external reference input features a typical input
impedance of 113kΩ and accepts an input voltage
from +2V to AVDD. Connect an external voltage
supply between REFI and GND to apply an ex-
ternal reference. Leave REFO unconnected. Visit
www.maxim-ic.com/products/references
available external voltage-reference devices.
Connect AVDD to REFI to use AVDD as the reference
voltage. Leave REFO unconnected.
Table 1. Operating Mode Truth Table*
* For the MAX5136/MAX5137, DAC2 and DAC3 do not exist. For the MAX5135/MAX5137, D0–D3 are don’t-care bits.
10
C7 C6 C5 C4 C3
MSB
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
______________________________________________________________________________________
0
0
0
0
0
0
1
1
CONTROL BITS
0
0
0
0
0
1
1
0
DAC
DAC
0
0
0
0
0
3
3
0
DAC
DAC
C2
0
0
0
0
1
2
2
0
DAC
DAC
C1
0
0
1
1
0
1
1
0
DAC
DAC
C0 D15 D14 D13 D12 D11 D10 D9
0
1
0
1
1
0
0
0
D15 D14 D13 D12 D11 D10 D9
D15 D14 D13 D12 D11 D10 D9
X
X
X
X
0
X
AVDD as Reference
External Reference
24-BIT WORD
X
X
X
X
0
X
X
X
X
X
0
X
for a list of
X
X
X
X
0
X
DAC
DAC
X
3
X
3
0
X
DATA BITS
DAC
DAC
X
2
X
2
0
X
DAC
DAC
LIN
X
X
X
1
1
The MAX5134–MAX5137 3-wire serial interface is com-
patible with MICROWIRE, SPI, QSPI, and DSPs (Figures
2, 3). The interface provides three inputs, SCLK, CS,
and DIN and one output, READY. Use READY to verify
communication or to daisy-chain multiple devices (see
the READY section). READY is capable of driving a
20pF load with a 30ns (max) delay from the falling edge
of SCLK. The chip-select input (CS) frames the serial
data loading at DIN. Following a chip-select input’s
high-to-low transition, the data is shifted synchronously
and latched into the input register on each falling edge
of the serial-clock input (SCLK). Each serial word is 24
bits. The first 8 bits are the control word followed by 16
data bits (MSB first), as shown in Table 1. The serial
input register transfers its contents to the input registers
after loading 24 bits of data. To initiate a new data
transfer, drive CS high, keep CS high for a minimum of
33ns before the next write sequence. The SCLK can be
either high or low between CS write pulses. Figure 1
shows the timing diagram for the complete 3-wire serial-
interface transmission.
DAC
DAC
D8
D8
D8
X
X
X
0
0
0
READY_EN
D7
D7
D7
X
X
X
X
0
D6–D0
LSB
D6
D6
X
X
X
X
X
0
Linearity Optimize DAC linearity.
through
Control
DESC
Power
LDAC
Write-
Write
NOP
NOP
CLR
No operation.
Move contents of input
to DAC registers
indicated by 1’s. No
effect on registers
indicated by 0’s.
Software clear.
Power down DACs
indicated by 1’s.
Set READY_EN = 1 to
enable READY.
Write to selected input
registers (DAC output
not affected).
Write to selected input
and DAC registers,
DAC outputs updated
(writethrough).
No operation.
Serial Interface
FUNCTION