PVZ2K203A01R00 Murata, PVZ2K203A01R00 Datasheet - Page 40

• Manufacturer Part Number: PVZ2K203A01R00
• Description: Trimmer Resistors - SMD 20K OHM SMD 2MM
• Manufacturer: Murata

Specifications of PVZ2K203A01R00

• Resistance: 20 KOhms
• Tolerance: 30 %
• Power Rating: 0.1 Watt (1/10 Watt)
• Operating Temperature Range: - 25 C to + 85 C
• Element Type: Carbon
• Number Of Turns: 1
• Product: Single-Turn Trimmer Potentiometers
• Taper: Linear
• Termination Style: SMD/SMT
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

!Note
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
1. Soldering
2. Mounting
(1) Standard soldering condition
(2) Cannot be soldered using the flow soldering
(3) The soldering iron should not come in contact
(4) Insufficient amounts of solder can lead to
(1) Use our standard land dimension. Excessive land
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
Notice (Rating)
the power depending on the resistance value.
potentiometer should not exceed (P.R)^1/2 or the
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
Notice (Soldering and Mounting)
(a) Reflow and flow soldering:
(b) Soldering iron:
Before using other soldering conditions than
those listed above, please consult with a Murata
factory representative prior to using. If the
soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature,
the trimmer capacitor may deviate from the
specified characteristics.
method. If you use the flow soldering method,
the trimmer potentiometer may not function.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals.
area causes displacement due to the effect of the
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
Refer to the standard temperature profile.
>Temperature of tip 260 deg.C max.
>Soldering time
>Diameter
>Wattage of iron
3 sec. max.
30W max.
2mm dia. max.
3. Cleaning
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(2) Do not apply excessive force (preferably 9.8N
(3) Do not warp and/or bend PC board to prevent
(4) In chip placers, the recommended size of the
(1) Isopropyl-alcohol and Ethyl-alcohol are
(2) The total cleaning time by cold dipping, vapor
(3) For ultra-sonic cleaning, the available
the following environmental conditions:
condition is as follows.
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
surface tension of the solder. Insufficient land
area leads to insufficient soldering strength of
the chip.
(Ref.; 1kgf) max.), when the trimmer
potentiometer is mounted to the PCB.
trimmer potentiometer from breakage.
cylindrical pick-up nozzle should be outer
dimension 4.0mm dia. and inner dimension 2.0mm
dia.
applicable solvents for cleaning. If you use any
other types of solvents, please consult with a
Murata factory representative prior to using.
and ultrasonic washing (conditions as below)
method should be less than 3 minutes.
Due to the ultra-sonic cleaning equipment's
peculiar self-resonance point and that the
cleaning compatibility usually depends on the jig
construction and/or the cleaning condition such
as the depth of immersion, please check the
>Power: 600W (67 liter) max.
>Frequency: 28kHz
>Temperature: Ambient temperature
PVG5/PV01 Series Notice
Continued on the following page.
R50E13.pdf 04.6.11
39
6