EP3C80F780C8 Altera, EP3C80F780C8 Datasheet - Page 15
![IC CYCLONE III FPGA 80K 780FBGA](/photos/6/72/67270/544-780-fbga_sml.jpg)
EP3C80F780C8
Manufacturer Part Number
EP3C80F780C8
Description
IC CYCLONE III FPGA 80K 780FBGA
Manufacturer
Altera
Series
Cyclone® IIIr
Datasheets
1.EP3C5F256C8N.pdf
(5 pages)
2.EP3C5F256C8N.pdf
(34 pages)
3.EP3C5F256C8N.pdf
(66 pages)
4.EP3C5F256C8N.pdf
(14 pages)
5.EP3C5F256C8N.pdf
(76 pages)
Specifications of EP3C80F780C8
Number Of Logic Elements/cells
81264
Number Of Labs/clbs
5079
Total Ram Bits
2810880
Number Of I /o
429
Voltage - Supply
1.15 V ~ 1.25 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
780-FBGA
For Use With
544-2411 - KIT DEV NIOS II CYCLONE III ED.
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Other names
544-2522
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP3C80F780C8N
Manufacturer:
ALTERA
Quantity:
380
Part Number:
EP3C80F780C8N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Early System Planning
Planning for On-Chip Debugging
© November 2008 Altera Corporation
f
f
The Quartus II software includes various debugging tools. The following is the list of
debugging tools and their use as well as the requirement for using the tools. Using
these tools in your design flow is optional, but is recommended.
SignalProbe Incremental Routing
The SignalProbe Incremental Routing feature allows you to route internal signals to
I/O pins without affecting the routing of the original design. Starting with a fully
routed design, you can select and route the signals for debugging to either previously
reserved or currently unused I/O pins. To use the SignalProbe feature, you must have
additional I/Os in your device for the signals to be routed to. These I/Os should be
routed out on the board in order for you to be able to probe the signals. You can use
the SignalProbe feature to monitor synchronous or asynchronous signals.
For more information about ways to use the SignalProbe feature for debugging, refer
to the
Handbook.
SignalTap II Embedded Logic Analyzer
The SignalTap II Embedded Logic Analyzer captures and displays real-time behavior
of your FPGA design's internal and I/O signals while the design is running at full
speed, without the need for additional I/O pins or external probes.
You can use the SignalTap II Embedded Logic Analyzer by instantiating the SignalTap
II Logic Analyzer megafunction and includes that in your design or by creating a
SignalTap II Logic Analyzer (.stp) file so that you do not need to modify your design.
The SignalTap II Embedded Logic Analyzer is suitable for capturing synchronous
signals and needs a clock signal from your design to control data acquisition. The
SignalTap II Embedded Logic Analyzer requires JTAG connection and communicates
with the device through an Altera download cable. Additional LEs and the M9K
memory are needed as well.
To minimize changes to your Cyclone III device's performance and reduce
compilation time when you use the SignalTap II Embedded Logic Analyzer,
back-annotate your design and use incremental compilation.
For more information about how to use the SignalTap II Embedded Logic Analyzer
for debugging, refer to the
Analyzer
Logic Analyzer Interface
Logic Analyzer Interface enables you to connect and transmit the internal FPGA
signals to an external logic analyzer or a mixed signal oscilloscope for analysis. You
can use this feature to connect a large set of internal device signals to a small number
of output pins for debugging purposes. This feature functions as a multiplexer and
you can select which of the signal groups to be connected to the output pins for
monitoring on the fly, without the need to recompile the design or reconfigure the
FPGA.
Quick Design Debugging Using SignalProbe
chapter in volume 3 of the Quartus II Handbook.
Design Debugging Using the SignalTap II Embedded Logic
chapter in volume 3 of the Quartus II
Page 15