EP3C120F780I7 Altera, EP3C120F780I7 Datasheet - Page 214

• Manufacturer Part Number: EP3C120F780I7
• Description: IC CYCLONE III FPGA 120K 780FBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C120F780I7

• Number Of Logic Elements/cells: 119088
• Number Of Labs/clbs: 7443
• Total Ram Bits: 3981312
• Number Of I /o: 531
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 780-FBGA
• Family Name: Cyclone III
• Number Of Logic Blocks/elements: 119088
• # I/os (max): 531
• Frequency (max): 437.5MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 119088
• Ram Bits: 3981312
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 780
• Package Type: FBGA
• For Use With: 544-2589 - KIT DEV EMB CYCLONE III EDITION544-2566 - KIT DEV DSP CYCLONE III EDITION544-2444 - KIT DEV CYCLONE III EP3C120
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Not Compliant

9–54
Figure 9–26. JTAG Configuration of Multiple Devices Using a Download Cable (2.5, 3.0, and 3.3-V V
Pins)
Notes to
(1) Connect these pull-up resistors to the V
(2) Connect the nCONFIG and MSEL[3..0] pins to support a non-JTAG configuration scheme. If you only use a JTAG configuration, connect the
(3) Pin 6 of the header is a V
(4) The nCE pin must be connected to ground or driven low for successful JTAG configuration.
(5) Power up the V
Cyclone III Device Handbook, Volume 1
Pin 1
10-Pin Male Header
Download Cable
nCONFIG pin to logic high and the MSEL[3..0] pins to ground. In addition, pull DCLK and DATA[0] either high or low, whichever is
convenient on your board.
MasterBlaster Serial/USB Communications Cable User
ByteBlaster II cables, this pin is connected to nCE when it is used for AS programming, otherwise it is a no connect.
to 2.5 V. Pin 4 of the header is a V
circuit boards, DC power supply, or 5.0 V from the USB cable. For this value, refer to the
Figure
V
CCA
(5)
10 kΩ
VIO
(3)
9–26:
1 kΩ
V
CC
CCA
of the ByteBlaster II, USB-Blaster, or ByteBlasterMV cable with a 2.5- V supply from V
V
CCA
10 kΩ
IO
(2)
(2)
(2)
(2)
(2)
reference voltage for the MasterBlaster output driver. V
V
CCIO
10
CC
(1)
DCLK
nST A TUS
DATA[0]
nCONFIG
MSEL[3..0]
nCEO
nCE
TDI
Chapter 9: Configuration, Design Security, and Remote System Upgrades in the Cyclone III Device Family
kΩ
power supply for the MasterBlaster cable. The MasterBlaster cable can receive power from either 5.0- or 3.3-V
TMS
(4)
Cyclone III Device
CCIO
Family
TCK
CONF_DONE
supply of the bank in which the pin resides.
TDO
V
Guide. In the ByteBlasterMV cable, this pin is a no connect. In the USB-Blaster and
CCIO
10
(1)
kΩ
(2)
(2)
(2)
(2)
(2)
V
CCIO
10
(1)
nST A TUS
DATA[0]
DCLK
nCONFIG
MSEL[3..0]
nCEO
nCE
TDI
kΩ
TMS
Cyclone III Device
(4)
IO
Family
must match the V
CONF_DONE
TCK
MasterBlaster Serial/USB Communications User
TDO
V
CCIO
10
CCA
CCA
(1)
kΩ
of the device. For this value, refer to the
. Third-party programmers must switch
© December 2009 Altera Corporation
(2)
(2)
(2)
(2)
(2)
V
CCIO
10
(1)
nST A TUS
DATA[0]
DCLK
nCONFIG
MSEL[3..0]
nCEO
nCE
TDI
CCIO
kΩ
TMS
(4)
Powering the JTAG
Cyclone III Device
Configuration Features
Family
TCK
CONF_DONE
TDO
V
CCIO
Guide.
10
(1)
kΩ