EP3C120F780I7 Altera, EP3C120F780I7 Datasheet - Page 62
![IC CYCLONE III FPGA 120K 780FBGA](/photos/6/72/67270/544-780-fbga_sml.jpg)
EP3C120F780I7
Manufacturer Part Number
EP3C120F780I7
Description
IC CYCLONE III FPGA 120K 780FBGA
Manufacturer
Altera
Series
Cyclone® IIIr
Datasheets
1.EP3C5F256C8N.pdf
(5 pages)
2.EP3C5F256C8N.pdf
(34 pages)
3.EP3C5F256C8N.pdf
(66 pages)
4.EP3C5F256C8N.pdf
(14 pages)
5.EP3C5F256C8N.pdf
(76 pages)
6.EP3C120F780I7.pdf
(274 pages)
Specifications of EP3C120F780I7
Number Of Logic Elements/cells
119088
Number Of Labs/clbs
7443
Total Ram Bits
3981312
Number Of I /o
531
Voltage - Supply
1.15 V ~ 1.25 V
Mounting Type
Surface Mount
Operating Temperature
-40°C ~ 100°C
Package / Case
780-FBGA
Family Name
Cyclone III
Number Of Logic Blocks/elements
119088
# I/os (max)
531
Frequency (max)
437.5MHz
Process Technology
65nm
Operating Supply Voltage (typ)
1.2V
Logic Cells
119088
Ram Bits
3981312
Operating Supply Voltage (min)
1.15V
Operating Supply Voltage (max)
1.25V
Operating Temp Range
-40C to 100C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
780
Package Type
FBGA
For Use With
544-2589 - KIT DEV EMB CYCLONE III EDITION544-2566 - KIT DEV DSP CYCLONE III EDITION544-2444 - KIT DEV CYCLONE III EP3C120
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
EP3C120F780I7
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Company:
Part Number:
EP3C120F780I7N
Manufacturer:
ALTERA
Quantity:
118
Page 62
“Board Design Considerations” on page 17
“Design and Compilation” on page 28
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Done
Done
N/A
N/A
Use the correct hardware setup when interfacing the Cyclone III device with 3.3/3.0/2.5-V
LVTTL/LVCMOS I/O systems.
Use the Quartus II software to check the restriction on the pin placement.
Minimize the simultaneous switching noise effect on the board with the following methods:
l
l
l
l
l
Connect the device unused pins to the board according to the behavior of the pins.
Terminate the signals according to the I/O standard and signal travel direction.
Perform board-level IBIS or HSPICE simulation.
Minimize the noise on the power planes.
Consider the power-up requirement and I/O behavior of the Cyclone III device during power
up.
Add the correct series resistance to the appropriate configuration signals based on the
configuration scheme used.
Use repeater buffers for the configuration signals when cascading Cyclone III devices in
multi-device configuration.
Ensure that the
Pull the configuration pins high or low through resistors with the recommended values.
Ensure that the devices in a configuration chain are connected properly.
To prevent the signals to the configuration pins from overshooting to more than 4.1 V, use
series resistors and buffers according to the setup.
Do not leave the
Connect the
For AP configuration, select the flash memory from the Intel P30 and P33 families that can
support 40-MHz clock.
Check the pin connection for other pins of the configuration device or flash memory.
Use the
Depending on the on-chip debugging method used, reserve additional resources such as
LE, memory and I/O, and route the JTAG pins out.
Consider the trade-off between schematics or HDL for your design entry based on your
design’s complexity.
Other than the Quartus II software, consider building your design with third-party EDA tools,
SOPC Builder, or IP cores.
If you are using HDL for design entry, use the recommended coding styles.
Distributing simultaneous switching I/O to different I/O banks
Setting unused I/O pins to V
Turning on the slow slew rate feature for the switching pins
Using a lower drive strength for the switching pins
Using the proper termination scheme for the switching pins
areset
MSEL
DCLK
JTAG
,
locked
pins to V
or
pins unconnected.
TCK
CC A
or
signals are clean.
pfdena
C C
or ground directly based on the configuration scheme used.
or ground
control signals as required by your design.
© November 2008 Altera Corporation
Design Checklist