XCV812E-7BG560C Xilinx Inc, XCV812E-7BG560C Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
XCV812E-7BG560C
Manufacturer Part Number
XCV812E-7BG560C
Description
IC FPGA 1.8V C-TEMP 560-MBGA
Manufacturer
Xilinx Inc
Series
Virtex™-E EMr
Datasheet
1.XCV405E-6FG676C.pdf
(118 pages)
Specifications of XCV812E-7BG560C
Number Of Logic Elements/cells
21168
Number Of Labs/clbs
4704
Total Ram Bits
1146880
Number Of I /o
404
Number Of Gates
254016
Voltage - Supply
1.71 V ~ 1.89 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
560-LBGA, Metal
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XCV812E-7BG560C
Manufacturer:
OMRON
Quantity:
1 001
Company:
Part Number:
XCV812E-7BG560C
Manufacturer:
XilinxInc
Quantity:
3 000
The sequence of operations necessary to configure a
Virtex-E FPGA serially appears in
At power-up, V
than 50 ms, otherwise delay configuration by pulling
PROGRAM Low until V
SelectMAP Mode
The SelectMAP mode is the fastest configuration option.
Byte-wide data is written into the FPGA with a BUSY flag
controlling the flow of data.
An external data source provides a byte stream, CCLK, a
Chip Select (CS) signal and a Write signal (WRITE). If
BUSY is asserted (High) by the FPGA, the data must be
held until BUSY goes Low.
Data can also be read using the SelectMAP mode. If
WRITE is not asserted, configuration data is read out of the
FPGA as part of a readback operation.
After configuration, the pins of the SelectMAP port can be
used as additional user I/O. Alternatively, the port can be
retained to permit high-speed 8-bit readback.
Retention of the SelectMAP port is selectable on a
design-by-design basis when the bitstream is generated. If
DS025-2 (v2.3) November 19, 2002
FPGA checks data using CRC
Figure 15: Serial Configuration Flowchart
FPGA enters start-up phase
and pulls INIT Low on error.
clearing pass and releases
causing DONE to go High.
If no CRC errors found,
configuration memory.
Serial Data In
FPGA starts to clear
Serial DOUT
FPGA makes a final
Once per bitstream,
R
INIT when finished.
(Output)
CC
(Output)
CCLK
must rise from 1.0 V to V
CC
Figure 16: Master-Serial Mode Programming Switching Characteristics
is valid.
Configuration Completed
Load a Configuration Bit
Set PROGRAM = High
Apply Power
Release INIT
Bitstream?
End of
T CKDS
INIT?
1 T DSCK
Figure
High
Yes
Low
No
2
15.
If used to delay
configuration
ds009_15_111799
CC
min in less
Virtex™-E 1.8 V Extended Memory Field Programmable Gate Arrays
www.xilinx.com
1-800-255-7778
Figure 16
Master-serial mode is selected by a <000> or <100> on the
mode pins (M2, M1, M0).
mation for
.
retention is selected, PROHIBIT constraints are required to
prevent SelectMAP-port pins from being used as user I/O.
Multiple Virtex-E FPGAs can be configured using the
SelectMAP mode, and be made to start-up simultaneously.
To configure multiple devices in this way, wire the individual
CCLK, Data, WRITE, and BUSY pins of all the devices in
parallel. The individual devices are loaded separately by
asserting the CS pin of each device in turn and writing the
appropriate data. See
Characteristics.
Write
Write operations send packets of configuration data into the
FPGA. The sequence of operations for a multi-cycle write
operation is shown below. Note that a configuration packet
can be split into many such sequences. The packet does
not have to complete within one assertion of CS, illustrated
in
1. Assert WRITE and CS Low. Note that when CS is
Figure
asserted on successive CCLKs, WRITE must remain
17.
shows the timing of master-serial configuration.
Figure 16
Table 11
Table 10
for SelectMAP Write Timing
shows the timing infor-
DS022_44_071201
Module 2 of 4
15