AT94K10AL-25AJI Atmel, AT94K10AL-25AJI Datasheet - Page 135

• Manufacturer Part Number: AT94K10AL-25AJI
• Description: IC FPSLIC 10K GATE 25MHZ 84PLCC
• Manufacturer: Atmel
• Series: FPSLIC®r

Specifications of AT94K10AL-25AJI

• Core Type: 8-bit AVR
• Speed: 25MHz
• Interface: I²C, UART
• Program Sram Bytes: 20K-32K
• Fpga Sram: 4kb
• Data Sram Bytes: 4K ~ 16K
• Fpga Core Cells: 576
• Fpga Gates: 10K
• Fpga Registers: 846
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 84-PLCC
• For Use With: ATSTK594 - BOARD FPSLIC DAUGHTER FOR STK500
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

1138I–FPSLI–1/08
This bit is set if an Overrun condition is detected, i.e., when a character already present in the
UDRn register is not read before the next character has been shifted into the Receiver Shift reg-
ister. The ORn bit is buffered, which means that it will be set once the valid data still in UDRn is
read.
The ORn bit is cleared (zero) when data is received and transferred to UDRn.
• Bit 2 - Res: Reserved Bit
This bit is reserved in the AT94K and will always read as zero.
• Bits 1 - U2X0/U2X1: Double the UART Transmission Speed
When this bit is set (one) the UART speed will be doubled. This means that a bit will be transmit-
ted/received in eight CPU clock periods instead of 16 CPU clock periods. For a detailed
description, see
• Bit 0 - MPCM0/MPCM1: Multi-processor Communication Mode
This bit is used to enter Multi-processor Communication Mode. The bit is set when the Slave
MCU waits for an address byte to be received. When the MCU has been addressed, the MCU
switches off the MPCMn bit, and starts data reception.
For a detailed description, see
UART0 Control and Status Registers – UCSR0B
UART1 Control and Status Registers – UCSR1B
• Bit 7 - RXCIE0/RXCIE1: RX Complete Interrupt Enable
When this bit is set (one), a setting of the RXCn bit in UCSRnA will cause the Receive Complete
interrupt routine to be executed provided that global interrupts are enabled.
• Bit 6 - TXCIE0/TXCIE1: TX Complete Interrupt Enable
When this bit is set (one), a setting of the TXCn bit in UCSRnA will cause the Transmit Complete
interrupt routine to be executed provided that global interrupts are enabled.
• Bit 5 - UDRIE0/UDREI1: UART Data Register Empty Interrupt Enable
When this bit is set (one), a setting of the UDREn bit in UCSRnA will cause the UART Data Reg-
ister Empty interrupt routine to be executed provided that global interrupts are enabled.
• Bit 4 - RXEN0/RXEN1: Receiver Enable
This bit enables the UART receiver when set (one). When the receiver is disabled, the TXCn,
ORn and FEn status flags cannot become set. If these flags are set, turning off RXENn does not
cause them to be cleared.
Bit
$0A ($2A)
Read/Write
Initial Value
Bit
$01 ($21)
Read/Write
Initial Value
7
RXCIE0
R/W
0
7
RXCIE1
R/W
0
“Double Speed Transmission” on page
6
TXCIE0
R/W
0
6
TXCIE1
R/W
0
“Multi-processor Communication Mode” on page
5
UDRIE0
R/W
0
5
UDRIE1
R/W
0
4
RXEN0
R/W
0
4
RXEN1
R/W
0
AT94KAL Series FPSLIC
TXEN0
R/W
TXEN1
R/W
3
0
3
0
138”.
2
CHR90
R/W
0
2
CHR91
R/W
0
1
RXB80
R
1
1
RXB81
R
1
0
TXB80
R/W
0
0
TXB81
R/W
0
133.
UCSR0B
UCSR1B
135