ZZL-4116-36LD Amphenol, ZZL-4116-36LD Datasheet - Page 30

• Manufacturer Part Number: ZZL-4116-36LD
• Description: Terminals 1P SOCKET GOLD
• Manufacturer: Amphenol
• Series: 48 Seriesr

Specifications of ZZL-4116-36LD

• Mil Type: MIL-DTL-26500
• Product Type: Contacts
• Shell Style: Receptacle
• Mounting Angle: Straight
• Termination Style: Crimp
• Contact Gender: Socket (Female)
• Contact Plating: Gold
• Features: Red
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Shielded/Coaxial Contacts
for MIL-C-26500 cylindrical connectors
** MS3191 tools are inactive for new procurement, but can be used if available.
*** Refer to illustration on page 29.
Shielded Contact Assembly Procedure
* Conforms to MIL-C-22520/2 specification.
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
#1 Shielded
#1 Shielded
#1 Shielded
#2 Shielded
#2 Shielded
(See below
next page)
Drawing
Type 1
Type 2
Type 3
Type 4
Type 5
and on
Slide sealing boot or sleeve and outer ferrule onto cable and strip cable as shown at right.
After stripping, slide spacer over center conductor as shown for Type 2 and Type 3.
For Type 3 slide spacer under wire braid.
Insert stripped center conductor into contact until wire shows through inspection hole and dielectric (Type 1,
Type 4 and Type 5) or spacer (Type 2 and Type 3) butts against contact. Fully seat contact in nest bushing
of crimp tool and crimp in one full stroke. (Follow same crimping procedures except use nest bushing crimp-
ing tool from table above).
Slightly flair out ends of wire braid to facilitate insertion of inner ferrule of body assembly.
Do not comb braid.
Install center contact in body assembly and slide inner ferrule underneath wire braid as shown. Push center
contact until it is locked in place in the body assembly. Pull lightly on cable to make sure that contact is
securely locked in place.
Slide outer ferrule over braid and up against body as shown. There should be no slack in the wire braid.
Crimp the outer ferrule with proper tool from table above. Then for Type 1, Type 3 and Type 5 slide sealing
sleeve toward contact until sleeve touches outer ferrule.
Insert the assembled shielded contact into the connector in the same way as the standard contact using
applicable insertion tool (see page 28). This completes assembly for Type 1, Type 2, Type 3 and Type 5.
To complete assembly for Type 4, push sealing boot into connector grommet until O-ring riser of boot snaps
into place and seals the assembly.
48-1226-02 Pin
48-1227-02 Socket
48-1227-50 Socket
48-1226-57 Pin
48-1227-57 Socket
48-1226-51, -54 Pin
48-1227-51, -54, -56 Socket
48-1226-55 Pin
48-1227-55 Socket
48-2187-02 Pin
48-2188-02 Socket
48-2187-50, -51 Pin
48-2188-50, -51, -53, -54
Socket
48-2187-52 Pin
48-2188-52 Socket
Contact Part No./
Contact Type
Shielded
.2189
.2189
.2189
.2344
.2189
.2189
.3125
Cable Stripping Dim.***
A
.0781
.0781
.0313
.0313
.1094
.1094
.1094
+.0156
–.0000
B
.1094
.1094
.1563
.1563
.1406
.1406
.1406
C
294-268*
294-289**
294-268*
294-289**
294-268*
294-289**
294-268*
294-289**
294-126**
294-243**
294-1166**†
294-358**
294-268*
294-1166**†
294-358**
294-268*
294-358**
294-268*
Tool
Amphenol Crimp Tools
28
† Same as 294-126, less positioners.
†† Including Hex Die Set
(Center Contact)
Nest Bushing
Turret Head
294-1631
294-1631
294-1631
294-1631
294-1014
294-1014
294-1015
299-1630
294-1014
294-1015
294-1630
294-1015
294-1630
Setting
Crimp
.030 -
.040
.030
.040
.037 -
.041
#3
#3
#1
#1
#1
#1
Crimping
294-529
294-529
294-528
294-528
294-529
294-528
294-528
294-530
Ferrule
Tool††
Outer
#22 AWG per MIL-C-7078
Type II and MIL-C-27500-22
KING RG-174/U, -188/U
RG-161/U, -179/U, -179A/U, -187/U
Raychem 9530A11
RG-180/U, -180A/U, -180B/U, -195/U
RG-178/U, -178A/U, -178B/U, -196-U
#18, 20, 22 AWG per MIL-C-7078, Type II
and MIL-C-27500-18, -20, -22 KING
Extruded Jacket
RG-180/U, -180A/U, -180B/U, -195/U
RG-59/U and 21-541
Cable Application
Type 1