PIC16F54-I/SS Microchip Technology, PIC16F54-I/SS Datasheet - Page 41
![IC MCU FLASH 512X12 20SSOP](/photos/6/58/65895/150-20-ssop_sml.jpg)
PIC16F54-I/SS
Manufacturer Part Number
PIC16F54-I/SS
Description
IC MCU FLASH 512X12 20SSOP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F54-ISS.pdf
(88 pages)
2.PIC16F54-ISS.pdf
(14 pages)
3.PIC16F57-ISO.pdf
(86 pages)
Specifications of PIC16F54-I/SS
Core Size
8-Bit
Program Memory Size
768B (512 x 12)
Core Processor
PIC
Speed
20MHz
Peripherals
POR, WDT
Number Of I /o
12
Program Memory Type
FLASH
Ram Size
25 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
20-SSOP
Controller Family/series
PIC16F
No. Of I/o's
12
Ram Memory Size
25Byte
Cpu Speed
20MHz
No. Of Timers
1
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164307 - MODULE SKT FOR PM3 28SSOPAC164014 - MODULE SKT PROMATEII 44PQFP
Eeprom Size
-
Data Converters
-
Connectivity
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC16F54-I/SS
Manufacturer:
MIC
Quantity:
20 000
8.3
A device may be powered down (Sleep) and later
powered up (wake-up from Sleep).
8.3.1
The Power-down mode is entered by executing a
SLEEP instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, the TO bit (STATUS<4>) is set, the PD
bit (STATUS<3>) is cleared and the oscillator driver is
turned off. The I/O ports maintain the status they had
before the SLEEP instruction was executed (driving
high, driving low or high-impedance).
It should be noted that a Reset generated by a WDT
time-out does not drive the MCLR/V
For lowest current consumption while powered down,
the T0CKI input should be at V
MCLR/V
(MCLR = V
8.3.2
The device can wake-up from Sleep through one of the
following events:
1.
2.
Both of these events cause a device Reset. The TO
and PD bits can be used to determine the cause of
device Reset. The TO bit is cleared if a WDT time-out
occurred (and caused wake-up). The PD bit, which is
set on power-up, is cleared when SLEEP is invoked.
The WDT is cleared when the device wakes from
Sleep, regardless of the wake-up source.
8.4
If the code protection bit has not been programmed, the
on-chip program memory can be read out for
verification purposes.
Once code protection is enabled, all program memory
locations above 0x3F read all ‘0’s. Program memory
locations 0x00-0x3F are always unprotected. The user
ID locations and the Configuration Word read out in an
unprotected fashion. It is possible to program the user
ID locations and the Configuration Word after code
protect is enabled.
© 2007 Microchip Technology Inc.
An external Reset input on MCLR/V
A Watchdog Timer time-out Reset (if WDT was
enabled).
PP
Power-Down Mode (Sleep)
Program Verification/Code
Protection
IH
pin must be at a logic high level
SLEEP
WAKE-UP FROM SLEEP
).
DD
PP
or V
pin low.
PP
SS
pin.
and the
8.5
Four memory locations are designated as user ID loca-
tions where the user can store checksum or other
code-identification numbers. These locations are not
accessible during normal execution, but are readable
and writable during Program/Verify.
Use only the lower 4 bits of the user ID locations and
always program the upper 8 bits as ‘1’s.
8.6
The PIC16F5X microcontrollers can be serially
programmed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground and programming
voltage. This allows customers to manufacture boards
with unprogrammed devices and then program the
microcontroller just before shipping the product. Thus,
the most recent firmware or custom firmware can be
programmed.
The device is placed into a Program/Verify mode by
holding the RB6 and RB7 pins low while raising the
MCLR (V
specification). RB6 becomes the programming clock
and RB7 becomes the programming data. Both RB6
and RB7 are Schmitt Trigger inputs in this mode.
A 6-bit command is then supplied to the device.
Depending on the command, 14 bits of program data
are then supplied to or from the device, depending if
the command was a Load or a Read. For complete
details of serial programming, please refer to the
respective Programming Specifications: “PIC16F54
Memory
“PIC16F57
(DS41208), and “PIC16F59 Memory Programming
Specification” (DS41243).
A typical In-Circuit Serial Programming connection is
shown in Figure 8-1.
Note:
User ID Locations
In-Circuit Serial Programming™
(ICSP™)
PP
Programming
Microchip will assign a unique pattern
number for QTP and SQTP requests. This
pattern number will be unique and trace-
able to the submitted code.
) pin from V
Memory
Programming
IL
Specification”
to V
PIC16F5X
IHH
(see programming
DS41213D-page 39
Specification”
(DS41207),