DS2141AQ/T&R Maxim Integrated Products, DS2141AQ/T&R Datasheet - Page 4
![IC CONTROLLER T1 5V 44-PLCC](/photos/6/62/66291/175-44-plcc_sml.jpg)
DS2141AQ/T&R
Manufacturer Part Number
DS2141AQ/T&R
Description
IC CONTROLLER T1 5V 44-PLCC
Manufacturer
Maxim Integrated Products
Datasheet
1.DS2141AQ.pdf
(39 pages)
Specifications of DS2141AQ/T&R
Controller Type
T1 Controller
Interface
Parallel/Serial
Voltage - Supply
4.5 V ~ 5.5 V
Current - Supply
10mA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
44-LCC, 44-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS2141AQ/T&RDS2141AQ/T&R
Manufacturer:
Maxim Integrated
Quantity:
10 000
PIN
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
RLOS/LOTC
SYMBOL
RCHCLK
RCHBLK
TCHBLK
SYSCLK
LI_CLK
RSYNC
TLCLK
LI_SDI
RNEG
RSER
RPOS
LI_CS
INT2
INT1
TYPE
I/O
O
O
O
O
O
O
O
O
O
O
I
I
Receive Channel Clock. 192 kHz clock which pulses high during
the LSB of each channel. Useful for parallel-to-serial conversion of
channel data, locating robbed-bit signaling bits, and for blocking
clocks in DDS applications. See Section 13 for timing details.
Receive Serial Data. Received NRZ serial data; updated on rising
edges of RCLK.
Receive Sync. An extracted pulse, one RCLK wide, is output at this
pin which identifies either frame (RCR2.4=0) or multiframe
boundaries (RCR2.4=1). If set to output frame boundaries, then via
RCR2.5, RSYNC can also be set to output double-wide pulses on
signaling frames. If the elastic store is enabled via the CCR1.2, then
this pin can be enabled to be an input via RCR2.3 at which a frame
boundary pulse is applied. See Section 13 for timing details.
Receive Bipolar Data Inputs. Sampled on falling edge of RCLK.
Tie together to receive NRZ data and disable bipolar violation
monitoring circuitry.
System Clock. 1.544 MHz or 2.048 MHz clock. Only used when
the elastic store function is enabled via the CCR. Should be tied low
in applications that do not use the elastic store.
Serial Port Data for the Line Interface. Connects directly to the
SDI input pin on the line interface.
Serial Port Clock for the Line Interface. Connects directly to the
SCLK input pin on the line interface.
Serial Port Chip Select for the Line Interface. Connects directly
to the
Receive/Transmit Channel Block. A user-programmable output
that can be forced high or low during any of the 24 T1 channels.
Useful for blocking clocks to a serial UART or LAPD controller in
application where not all T1 channels are used such as Fractional
T1, 384K bps service, 768K bps, or ISDN-PRI. Also useful for
locating individual channels in drop-and-insert applications. See
Section 13 for timing details.
Receive Loss of Sync/Loss of Transmit Clock. A dual function
output. If CCR1.6=0, then this pin will toggle high when the
synchronizer is searching for the T1 frame and multiframe. If
CCR1.6=1, then this pin will toggle high when the TCLK pin has
not been toggled for 5 ms.
Receive Alarm Interrupt 2. Flags host controller during conditions
defined in Status Register 2. Active low, open drain output.
Receive Alarm Interrupt 1. Flags host controller during alarm
conditions defined in Status Register 1. Active low, open drain
output.
Transmit Link Clock. 4 kHz or 2 kHz (ZBTSI) demand clock for
the TLINK input. See Section 13 for timing details.
CS
input pin on the line interface.
4 of 39
DESCRIPTION
DS2141A