DS21FF42 Maxim Integrated Products, DS21FF42 Datasheet - Page 41

• Manufacturer Part Number: DS21FF42
• Description: IC FRAMER T1 4X4 16CH 300-BGA
• Manufacturer: Maxim Integrated Products

Specifications of DS21FF42

• Controller Type: T1 Framer
• Interface: Parallel/Serial
• Voltage - Supply: 2.97 V ~ 3.63 V
• Current - Supply: 300mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 300-BGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

CCR7: COMMON CONTROL REGISTER 7 (Address=0A Hex)
REMOTE LOOPBACK
When CCR7.6 is set to a one, the DS21Q42 will be forced into Remote LoopBack (RLB). In this
loopback, data input via the RPOS and RNEG pins will be transmitted back to the TPOS and TNEG pins.
Data will continue to pass through the receive side framer of the DS21Q42 as it would normally and the
data from the transmit side formatter will be ignored. Please see Figure 6-1 for more details.
10.
There is a set of nine registers per channel that contain information on the current real time status of a
framer in the DS21Q42, Status Register 1 (SR1), Status Register 2 (SR2), Receive Information Registers
1 to 3 (RIR1/RIR2/RIR3) and a set of four registers for the onboard HDLC and BOC controller. The
specific details on the four registers pertaining to the HDLC and BOC controller are covered in Section
19 but they operate the same as the other status registers in the DS21Q42 and this operation is described
below.
When a particular event has occurred (or is occurring), the appropriate bit in one of these nine registers
will be set to a one. All of the bits in SR1, SR2, RIR1, RIR2, and RIR3 registers operate in a latched
fashion. This means that if an event or an alarm occurs and a bit is set to a one in any of the registers, it
will remain set until the user reads that bit. The bit will be cleared when it is read and it will not be set
again until the event has occurred again (or in the case of the RBL, RYEL, LRCL, and RLOS alarms, the
bit will remain set if the alarm is still present). There are bits in the four HDLC and BOC status registers
that are not latched and these bits are listed in Section 19.
(MSB)
SYMBOL
–
RESR
TESR
STATUS AND INFORMATION REGISTERS
RLB
–
–
–
–
–
RLB
POSITION
CCR7.7
CCR7.6
CCR7.5
CCR7.4
CCR7.3
CCR7.2
CCR7.1
CCR7.0
RESR
NAME AND DESCRIPTION
Not Assigned. Should be set to zero when written to.
Remote Loopback.
0 = loopback disabled
1 = loopback enabled
Receive Elastic Store Reset. Setting this bit from a zero to a
one will force the receive elastic store to a depth of one
frame. Receive data is lost during the reset. Should be
toggled after RSYSCLK has been applied and is stable. Do
not leave this bit set high.
Transmit Elastic Store Reset. Setting this bit from a zero to
a one will force the transmit elastic store to a depth of one
frame. Transmit data is lost during the reset. Should be
toggled after TSYSCLK has been applied and is stable. Do
not leave this bit set high.
Not Assigned. Should be set to zero when written to.
Not Assigned. Should be set to zero when written to.
Not Assigned. Should be set to zero when written to.
Not Assigned. Should be set to zero when written to.
TESR
41 of 114
–
–
–
(LSB)
–