DNC-T2006-020 NCC, DNC-T2006-020 Datasheet

no-image

DNC-T2006-020

Manufacturer Part Number
DNC-T2006-020
Description
Dust Collector; 120 VAC; 2 VA (Max.); 50/60 Hz; -40 to degC
Manufacturer
NCC
Type
Dust Collectorr
Datasheet

Specifications of DNC-T2006-020

Accuracy
±3% over temperature and voltage range
Dimensions
6.75"×4.75"×1.103"
Frequency
50/60 Hz
Number Of Outputs
6
Output Type
Solid State, 150 VA max
Power Consumption
6.30 VA max plus load
Primary Type
Controller
Standards
UL, cUL
Temperature, Operating
–40 to +66°C
Voltage, Supply
95 to 265 VAC
IFCB
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: 800-323-2593 • 630-231-5900 • FAX: 630-231-1377 • www.nationalcontrols.com
AC Input, Pulse Cleaning of
Bag House Dust Collectors
Models DNC-T2003 through DNC-T2032
FEATURES
OPERATING LOGIC
The DNC-T2003 through DNC-T2032 con-
trols are output sequencers with an ad
justable ON TIME, OFF TIME, and LAST
OUTPUT. Upon application of power to
the L1 and L2 terminals with the high pres-
sure switch co ntacts c losed, the OFF
TIME is initiated. At the end o f the preset
OFF TIME, output 1will turn on for the pre-
set ON TIME. The control will cycle through
all selected outputs until the high and low
pressure switch contacts are opened. If
the pressure switch contacts open dur-
ing the ON TIME, the output will complete
the active ON cycle. The next time the high
pressure switch is closed the next output in
the sequence is fired. Pressure monitoring
with no hysteresis is achieved by using only
Universal voltage input: 95 to 265 VAC
50/60 Hz
One SKU: covers all voltages and time
ranges required in your application
Advanced surface mount component
technology: extremely reliable and trou-
ble free operation
Digital microprocessor controlled cir-
cuitry: for precise pulse timing
Non-Volatile memory: for retaining pro-
grammed settings
3 digit, 7 segment numeric display: for
ease of viewing controller operation
Easily programmable: on/off times and
last output used via keypad
Small footprint: same size for 3, 6 and
10 output control
Time Ranges for all applications: On
Time: 50ms to 600 sec, Off time: 1 to
999 sec
2 modes of operation: can be operated
continuously or on demand via external
pressure switch
Finger safe terminations: reliable elec-
trical connections and increases safety
RoHS construction: suited for global
applications
Supplied on metal chassis: for mount-
ing directly in a NEMA 4 box
Retrofit models available: for direct
drop in replacement of former product
UL/CUL: File # E65038
DUST COLLECTOR CONTROLS
a high pressure switch. Placing a jumper
across the high pressure input forces the
control to run continuously.
Note: Controls are shipped with jumper across pressure switch
terminals
PROGRAMMING
Programming is accomplished using 3
buttons: down, up, and select
Down: Decrements the active parameter
Up: Increments the active parameter
Select: Toggles amongst the adjustable
parameters: on-time, off-time, and last
output
Programming Mode Timeout: 60 seconds
TEST & DEFAULT MODES
Test mode is entered by pressing and hold-
ing the select button for 3 seconds while the
unit is in the normal operating mode. Once
in test mode, the display will show tSt.
Pressing the up or down arrow buttons
toggles amongst outputs, and pressing
select pulses the selected output for the
preset ON-TIME. Pressing the select button
while the display shows tSt will change the
display to “dFt”. While the display shows
“dFt”, the up and down arrows toggle
amongst “y”, “n”, and “dFt”. Pressing select
when the message is “y” will set all ad just-
able parameters to the factory defaults. At
any time in test and default modes, pressing
and holding the select button for 1.5 sec-
onds will revert the controller back to the
normal operating mode.
HI CM LO
L1L2
120 VAC
Solenoid
Outputs
Latch
Last
S
Timer No. 1
Pressure
Switch
10
“A”
“B”
Note: Must
connect L1 of
first unit to L1 of
second unit.
Same with L2.
Last
output
used
Alternate — Action
Latching Relay
“A”
“B”
HI CM LO
L1L2
120 VAC
Solenoid
Outputs
Latch
Last
Timer No. 2
S
Pressure
Switch
10
Last
output
used

Related parts for DNC-T2006-020

DNC-T2006-020 Summary of contents

Page 1

... Retrofit models available: for direct drop in replacement of former product ● UL/CUL: File # E65038 OPERATING LOGIC The DNC-T2003 through DNC-T2032 con- trols are output sequencers with an ad justable ON TIME, OFF TIME, and LAST OUTPUT. Upon application of power to the L1 and L2 terminals with the high pres- sure switch co ntacts c losed, the OFF TIME is initiated ...

Page 2

... DNC–T2006–020 6 6.75” DNC–T2010–020 10 6.75” DNC–T2020–020 20 8.75” DNC–T2032–020 32 8.75” DNC–T2006–R20 6 8.75” DNC–T2010–R20 10 8.75” DNC–T2020–R20 20 10.75” DNC–T2032–R20 32 12.75” Caution: 1 ...

Related keywords