AT-FM-10K BANNER ENGINEERING, AT-FM-10K Datasheet - Page 2

• Manufacturer Part Number: AT-FM-10K
• Description: Control Module, Two Hand; Solid State (NPN, PNP), Relay (Auxiliary N.C.); 200 W
• Manufacturer: BANNER ENGINEERING
• Type: Safetyr

Specifications of AT-FM-10K

• Brand/series: Duo-Touch
• Contact Form: SPDT-NO/NC
• Dimensions: 22.5mmW×84mmH×118mmD
• Enclosure Rating: IP20
• Indicator: 4 Green LED, 1 Red LED
• Ip Rating: IP20
• Material, Casing: Polycarbonate
• Mounting: DIN Rail
• Mounting Type: DIN Rail
• Number Of Outputs: 4
• Output Type: Digital/Relay
• Power Consumption: 200 W
• Primary Type: Controller
• Standards: cULus, cCSAus, CE
• Temperature, Operating: 0 to +50 °C
• Voltage, Supply: 24 VDC
• Coil Voltage Vac Nom: 24V
• Coil Voltage Vdc Nom: 24V
• Contact Current Max: 6A
• Contact Voltage Ac Nom: 250V
• Contact Voltage Dc Nom: 24V
• Contact Configuration: SPST-NO
• No. Of Poles: 1
• Lead Free Status / Rohs Status: RoHS Exempt Product
• For Use With: Two-Hand Control

DUO-TOUCH
NOTE: Do not attempt any repairs to the DUO-TOUCH SG Two-Hand Control Module.
If it ever becomes necessary to return a DUO-TOUCH SG Safety Module to the factory,
please do the following:
1) Contact the Banner Factory Application Engineering Group at the address or
2) Pack the component carefully. Damage which occurs in return shipping is not
Figure 5. DUO-TOUCH SG Safety Module dimensions
10
A1
Power
Output
Y2
Fault
S12
S23
In 1
In 2
at the numbers listed at the bottom of the back page. They will attempt to
troubleshoot the system from your description of the problem. If they conclude
that a component is defective, they will issue an RMA (Return Merchandise
Authorization) number for your paperwork, and give you the proper shipping
address.
covered by warranty.
13
14
S11
S21
P/N 64137 rev. C
It contains no field-replaceable components. Return it to the factory for
warranty repair or replacement.
23
AT-FM-10K
24
13
14
Machine
Safety
23
24
S13
S22
Y1
A2
K1
K2
22.5 mm
84.0 mm
(0.89")
(3.31")
®
SG –
Model AT-FM-10K Two-Hand Control Module
Repairs
118.0 mm
(4.65")
Figure 6. To remove a terminal block,
and the Module will not reset, do not tap,
strike, or otherwise attempt to correct the
fault by a physical impact to the housing.
An internal relay may have failed in such a
manner that its replacement is required.
If the Module is not immediately replaced
or repaired, multiple simultaneous failures
may accumulate such that the safety
function can not be guaranteed.
!
insert a small screwdriver into
the slot as shown, and pry to
loosen.
CAUTION ...
Module After Failure
If an internal fault has occurred
Abuse of
P o
F a
I n p
I n p
S S
M u
O u
w e
u l t
I
t p u
u t
u t
t i n
r
1
2
g
t
K 1 K 2
A 1
3 1
1 3
S 1 2
3 1
K 1
K 2
1 4
A 2
S 1 1
3 2
2 3
B 1
3 2
S 1 3
2 4
Z 3
X 3
S 2 2
Z 4
X 4
S 2 1
X 1
Y 1
X 5
S 2 3
X 2
Y 2
X 6
Y 3 0
M 1
1