AT-FM-10K BANNER ENGINEERING, AT-FM-10K Datasheet - Page 3

• Manufacturer Part Number: AT-FM-10K
• Description: Control Module, Two Hand; Solid State (NPN, PNP), Relay (Auxiliary N.C.); 200 W
• Manufacturer: BANNER ENGINEERING
• Type: Safetyr

Specifications of AT-FM-10K

• Brand/series: Duo-Touch
• Contact Form: SPDT-NO/NC
• Dimensions: 22.5mmW×84mmH×118mmD
• Enclosure Rating: IP20
• Indicator: 4 Green LED, 1 Red LED
• Ip Rating: IP20
• Material, Casing: Polycarbonate
• Mounting: DIN Rail
• Mounting Type: DIN Rail
• Number Of Outputs: 4
• Output Type: Digital/Relay
• Power Consumption: 200 W
• Primary Type: Controller
• Standards: cULus, cCSAus, CE
• Temperature, Operating: 0 to +50 °C
• Voltage, Supply: 24 VDC
• Coil Voltage Vac Nom: 24V
• Coil Voltage Vdc Nom: 24V
• Contact Current Max: 6A
• Contact Voltage Ac Nom: 250V
• Contact Voltage Dc Nom: 24V
• Contact Configuration: SPST-NO
• No. Of Poles: 1
• Lead Free Status / Rohs Status: RoHS Exempt Product
• For Use With: Two-Hand Control

Supply Voltage and Current
Supply Protection Circuitry
Output Configuration
Output Response Time
Input Requirements
Simultaneity Monitoring
Period
Status Indicators
Housing
Mounting
Vibration Resistance
Operating Conditions
Dimensions
Safety Category
Certifications
DUO-TOUCH
Protected against transient voltages and reverse polarity
Each normally open output channel is a series connection of contacts from two forced-guided (positive-
guided) relays, K1-K2.
Contacts: AgNi, 5 µm gold-plated
Low Current Rating:
Caution: The 5 µm gold-plated contacts allow the switching of low current/low voltage. In these low-
To preserve the gold plating on the contacts, the following max. values should not be exceeded at any time:
High Current Rating:
If higher loads must be switched through one or more of the contacts, the minimum and maximum values
of the contact(s) changes to:
Mechanical life: 50,000,000 operations
Electrical life: 150,000 operations typical, @ 200 W (1,500 VA) switched power, resistive load.
Note: Transient suppression is recommended when switching inductive loads. Install suppressors
35 milliseconds maximum ON and OFF
Outputs from actuating devices must each be capable of switching up to 20 mA @ 12V dc.
≤ 500 milliseconds
4 green LED indicators:
Power ON
Input 1 energized
Input 2 energized
Output
Polycarbonate. Rated NEMA 1 (IEC IP20)
Mounts to standard 35 mm DIN rail track. Safety Module must be installed inside an enclosure rated
NEMA 3 (IEC IP54), or better.
10 to 55 Hz @ 0.35 mm displacement per IEC 68-2-6
Temperature: 0° to +50°C (+32° to 122°F)
Maximum Relative Humidity: 90% @ +50°C (non-condensing)
Heat Dissipation Considerations: See page 4.
See Figure 5.
4 per ISO 13849-1; Type IIIC per ISO 13851 (EN574) (when used with STBs or hard contacts)
24V ac/dc ±15% @ 150 mA
Min. voltage: 1V ac/dc
Min. current: 5 mA ac/dc
Min. power: 5 mW (5 mVA)
Min. voltage: 15V ac/dc
Min. current: 250 mA ac/dc
Min. power: 5 W (5 VA)
across load. Never install suppressors across output contacts (see Warning, page 7).
power applications, multiple contacts can also be switched in series (e.g., “dry switching”).
®
C
SG –
Specifications
R
US
Model AT-FM-10K Two-Hand Control Module
Max. voltage: 60V
Max. current: 300 mA
Max. power: 7 W (7 VA)
Max. voltage: 250V ac/dc
Max. current: 6 A
Max. power: 200 W (1,500 VA)
1 red LED indicator:
Fault
P/N 64137 rev. C
11