CY7C68001-56LTXC Cypress Semiconductor Corp, CY7C68001-56LTXC Datasheet - Page 34
![IC USB EZ-USB SX2 HS 56VQFN](/photos/6/84/68461/cy7c68001-56ltxc_sml.jpg)
CY7C68001-56LTXC
Manufacturer Part Number
CY7C68001-56LTXC
Description
IC USB EZ-USB SX2 HS 56VQFN
Manufacturer
Cypress Semiconductor Corp
Series
CY7Cr
Type
USBr
Specifications of CY7C68001-56LTXC
Protocol
USB 2.0
Voltage - Supply
3 V ~ 3.6 V
Mounting Type
Surface Mount
Package / Case
56-VQFN Exposed Pad, 56-HVQFN, 56-SQFN, 56-DHVQFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Drivers/receivers
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
428-2932
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CY7C68001-56LTXC
Manufacturer:
CYPRESS/赛普拉斯
Quantity:
20 000
Figure 13-16.
signals during a synchronous FIFO read using IFCLK as the
synchronizing clock. The diagram illustrates a single read
followed by a burst read.
■
Note: t
running at 48 MHz, the FIFO address setup time is more than
one IFCLK cycle.
■
■
Document #: 38-08013 Rev. *J
At t = 0 the FIFO address is stable and the signal SLCS is
asserted (SLCS may be tied low in some applications).
At = 1, SLOE is asserted. SLOE is an output enable only, whose
sole function is to drive the data bus. The data that is driven on
the bus is the data that the internal FIFO pointer is currently
pointing to. In this example it is the first data value in the FIFO.
Note: the data is pre-fetched and is driven on the bus when
SLOE is asserted.
At t = 2, SLRD is asserted. SLRD must meet the setup time of
t
the IFCLK) and maintain a minimum hold time of t
from the IFCLK edge to the deassertion of the SLRD signal).
SRD
PKTEND
FIFOADR
FLAGS
DATA
IFCLK
SLWR
SLCS
SFA
(time from asserting the SLRD signal to the rising edge of
has a minimum of 25 ns. This means when IFCLK is
shows the timing relationship of the SLAVE FIFO
t=0
Figure 13-18. Slave FIFO Synchronous Write Sequence and Timing Diagram
t
SFA
t=1
t=2
t
t
SFD
SWR
t
N
IFCLK
t=3
t
FDH
t
WRH
t
XFLG
t
FAH
RDH
(time
T=0
t
SFA
■
The same sequence of events are shown for a burst read and
are marked with the time indicators of T = 0 through 5. Note: For
the burst mode, the SLRD and SLOE are left asserted during the
entire duration of the read. In the burst read mode, when SLOE
is asserted, data indexed by the FIFO pointer is on the data bus.
During the first read cycle, on the rising edge of the clock the
FIFO pointer is updated and increments to point to address N+1.
For each subsequent rising edge of IFCLK, while the SLRD is
asserted, the FIFO pointer is incremented and the next data
value is placed on the data bus.
If the SLCS signal is used, it must be asserted with SLRD, or
before SLRD is asserted (that is, the SLCS and SLRD signals
must both be asserted to start a valid read condition).
The FIFO pointer is updated on the rising edge of the IFCLK,
while SLRD is asserted. This starts the propagation of data
from the newly addressed location to the data bus. After a
propagation delay of t
IFCLK) the new data value is present. N is the first data value
read from the FIFO. In order to have data on the FIFO data
bus, SLOE MUST also be asserted.
T=1
T=2
>= t
t
SFD
SWR
N+1
t
FDH
T=3
t
SFD
N+2
XFD
t
FDH
T=4
(measured from the rising edge of
t
SFD
t
N+3
SPE
[13]
>= t
t
t
XFLG
FDH
T=5
t
WRH
PEH
CY7C68001
t
FAH
Page 34 of 45
[+] Feedback