AFM30P-060AS SMC Corporation, AFM30P-060AS Datasheet
![no-image](/images/no-image-200.jpg)
AFM30P-060AS
Manufacturer Part Number
AFM30P-060AS
Description
Filter Element for AFM30 series Mist Separators
Manufacturer
SMC Corporation
Datasheet
1.AFM30P-060AS.pdf
(1 pages)
Specifications of AFM30P-060AS
Product Type
Element
For Use With
AFM30 Series
AFM20
Flow Characteristics
Construction
AFM20
AFM30/40
Component Parts
Replacement Parts
Note 1) Including O-Ring. Please contact SMC regarding the bowl assembly supply for PSI and °F unit specifications.
Note 2) Bowl assembly for AFM30 to AFM40-06 includes a bowl guard (steel band material).
No.
No.
q
w
e
r
Description
Element assembly
Bowl O-ring
Bowl assembly
Body
Description
Flow rate (
Zinc die-casted
IN
(1)
IN
AFM20
Material
l
/min (ANR))
NBR
Drain
PC
—
Drain
(Representative values)
AFM20P-060AS
AFM30, AFM40, AFM40-06
C2SFP-260S
ø10 One-touch fitting
Material
AFM20
Aluminum die-casted
OUT
C2SF
q
e
w
r
OUT
q
e
w
r
AFM30P-060AS
AFM30
C3SFP-260S
Float type auto-drain (N.C.)
C3SF
AFM30
N.C.
ø10 One-touch fitting
Float type auto-drain
(2)
Part no.
M5 x 0.8
Flow rate (
Mist Separator
AFM40P-060AS
C4SFP-260S
Platinum silver
C4SF
AFM40
Note
l
/min (ANR))
N.O.
(2)
AFM40P-060AS
C4SFP-260S
AFM40-06
C4SF
Series
(2)
AFM40
1. Install an air filter (Series AF) as a
2. Do not install on the inlet side of the
1. Replace the element every 2 years or
1. Design the system so that the mist
1. Do not allow air flow that exceeds the
2. Do not use in a low pressure
Be sure to read before handling.
Refer to pages 14-21-3 to 14-21-4
for
Common Precautions.
when the pressure drop becomes 0.1
MPa, whichever comes first, to prevent
damage to the element.
separator is installed in a pulsation-free
location.
internal and external pressure inside
the element should be kept within 0.1
MPa, as exceeding this value could
cause damage.
rated flow. If the air flow is allowed
outside the range of the rated flow even
momentarily, drainage and lubricant
may splash at the outlet side or cause
damage to the component.
application (such as a blower). F.R.L.
unit has its own minimum operating
pressure depending on the equipment
and is designed specifically to function
with compressed air. If used below the
minimum operating pressure, a loss of
performance and malfunction can
occur. Please contact SMC if an
application under such conditions
cannot be avoided.
preliminary filter on the inlet side of the
mist separator to prevent premature
clogging.
dryer as this can cause premature
clogging of the element.
AFM20/30/40
Warning
Caution
Caution
Caution
Safety
Precautions
Maintenance
Flow rate (
The
Air Supply
Selection
Design
Instructions
difference
l
/min (ANR))
: When saturated with oil
: Initial state
14-2-41
between
and
F.R.L.
AV
AU
AF
AR
IR
VEX
AMR
ITV
IC
VBA
VE
VY1
G
PPA
AL