DP83848KSQ/NOPB National Semiconductor, DP83848KSQ/NOPB Datasheet - Page 10

• Manufacturer Part Number: DP83848KSQ/NOPB
• Description: IC TXRX ETHERNET PHYTER 40-LLP
• Manufacturer: National Semiconductor
• Type: Transceiverr

Specifications of DP83848KSQ/NOPB

• Number Of Drivers/receivers: 1/1
• Protocol: Ethernet
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 40-LLP
• For Use With: DP83848K-MAU-EK - BOARD EVALUATION DP83848K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DP83848KSQ; DP83848KSQTR

www.national.com
1.3 CLOCK INTERFACE
RX_ER
RXD_0
RXD_1
RXD_2
RXD_3
CRS/CRS_DV
COL
X1
X2
Signal Name
Signal Name
S, O, PU
S, O, PD
S, O, PU
S, O, PU
Type
Type
O
I
Pin #
Pin #
34
36
37
38
39
33
35
28
27
MII RECEIVE ERROR: Asserted high synchronously to RX_CLK
to indicate that an invalid symbol has been detected within a re-
ceived packet in 100 Mb/s mode.
RMII RECEIVE ERROR: Assert high synchronously to X1 when-
ever it detects a media error and RX_DV is asserted in 100 Mb/s
mode.
This pin is not required to be used by a MAC, in either MII or RMII
mode, since the Phy is required to corrupt data on a receive error.
MII RECEIVE DATA: Nibble wide receive data signals driven syn-
chronously to the RX_CLK, 25 MHz for 100 Mb/s mode, 2.5 MHz
for 10 Mb/s mode). RXD[3:0] signals contain valid data when
RX_DV is asserted.
RMII RECEIVE DATA: 2-bits receive data signals, RXD[1:0], driv-
en synchronously to the X1 clock, 50 MHz.
MII CARRIER SENSE: Asserted high to indicate the receive me-
dium is non-idle.
RMII CARRIER SENSE/RECEIVE DATA VALID: This signal
combines the RMII Carrier and Receive Data Valid indications.
For a detailed description of this signal, see the RMII Specifica-
tion.
MII COLLISION DETECT: Asserted high to indicate detection of
a collision condition (simultaneous transmit and receive activity)
in 10 Mb/s and 100 Mb/s Half Duplex Modes.
While in 10BASE-T Half Duplex mode with heartbeat enabled this
pin is also asserted for a duration of approximately 1 s at the end
of transmission to indicate heartbeat (SQE test).
In Full Duplex Mode, for 10 Mb/s or 100 Mb/s operation, this sig-
nal is always logic 0. There is no heartbeat function during 10
Mb/s full duplex operation.
RMII COLLISION DETECT: Per the RMII Specification, no COL
signal is required. The MAC will recover CRS from the CRS_DV
signal and use that along with its TX_EN signal to determine col-
lision.
CRYSTAL/OSCILLATOR INPUT: This pin is the primary clock
reference input for the DP83848K and must be connected to a 25
MHz 0.005% (+50 ppm) clock source. The DP83848K supports
either an external crystal resonator connected across pins X1 and
X2, or an external CMOS-level oscillator source connected to pin
X1 only.
RMII REFERENCE CLOCK: This pin is the primary clock refer-
ence input for the RMII mode and must be connected to a 50 MHz
0.005% (+50 ppm) CMOS-level oscillator source.
CRYSTAL OUTPUT: This pin is the primary clock reference out-
put to connect to an external 25 MHz crystal resonator device.
This pin must be left unconnected if an external CMOS oscillator
clock source is used.
10
Description
Description