SV1100-5FU SMC Corporation, SV1100-5FU Datasheet - Page 6

• Manufacturer Part Number: SV1100-5FU
• Description: Solenoid Valve, 5 port, 2 posit single, 24VDC, ind light, surge suppr
• Manufacturer: SMC Corporation
• Type: Solenoidr

Specifications of SV1100-5FU

• Brand/series: SV Series
• Configuration: 2-Position Single
• Primary Type: Solenoid Valve
• Voltage, Coil: 24 VDC

1. These products are intended for use in general factory
2. Do not use in an explosive atmosphere, environment with
3. Work such as transporting, installing, piping, wiring,
4. Install an external emergency stop circuit that can
5. Do not remodel these products, as there is a danger of
6. Do not wipe the product with chemicals, etc.
1. Read the instruction manual carefully, strictly observe the
2. Do not drop these products or submit them to strong
3. In locations with poor electrical conditions, take steps to
4. Do not touch connector terminals or internal substrates
5. Operate at an ambient temperature that is within the
6. Keep wire scraps and other extraneous material from
7. Give consideration to the operating environment
8. Obey the proper tightening torque.
Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 1-7-2.
automation equipment.
Avoid using these products in machinery/equipment which
affects human safety, and in cases where malfunction or
failure can result in extensive damage.
inflammable gases, or corrosive atmosphere.
This can cause injury or fire, etc.
operation, control and maintenance should be performed
by personnel with specialized knowledge.
There is a danger of electrocution, injury or fire, etc.
promptly stop operation and shut off the power supply.
injury and damage.
precautions and operate within the range of the
specifications.
impacts. This can cause damage, failure or malfunction,
etc.
ensure a steady flow of the rated power supply. Use of a
voltage outside of the specifications can cause
malfunction, damage to the unit, electrocution or fire, etc.
when current is being supplied. There is a danger of
malfunction, damage to the unit or electrocution if
connector terminals or internal substrates are touched
when current is being supplied.
Be sure that the power supply is OFF when adding or
removing manifold valves or input blocks, etc., or when
connecting or disconnecting connectors.
specifications. Even when the ambient temperature range
is within the specifications, do not use in locations where
there are rapid temperature changes.
getting inside these products. This can cause fire, failure
or malfunction, etc.
depending on the type of enclosure being used.
To achieve IP65 or IP67 protection, provide appropriate wiring
between
communication connectors and cables with M12 connectors.
Also, provide waterproof caps when there are unused ports,
and perform proper mounting of input units, input bolcks, SI
units and manifold valves, etc. Provide a cover or other
protection for applications in which there is constant exposure
to water.
There is a possibility of damaging threads if tightening
exceeds the tightening torque range.
Warning
Caution
all
units
using
Serial Wiring EX500/EX250/EX120 Precautions
electrical
wiring
Precautions 4
cables,
10. When these products are installed in equipment, provide
11. Since these products are components that are used after
12. Do not remove the name plate.
13. Perform periodic inspections and confirm normal
1. Operation is possible with a single power supply or a
2. Use the following UL approved products for DC power
9. Provide adequate protection when operating in locations
1. Be careful of mis-wiring. This can cause malfunction,
2. To prevent noise and surge in signal lines, keep all wiring
3. Check wiring insulation, as defective insulation can cause
4. Do not bend or pull cables repeatedly, and do not place
separate power supply. However, be sure to provide two
wiring systems (one for solenoid valves, and one for input
and control units).
supply combinations.
1) Controlled voltage current circuit conforming to UL508
2) A circuit (class 2 circuit) with maximum 30 Vrms (42.4 V
such as the following:
• Where noise is generated by static electricity, etc.
• Where there is a strong electric field
• Where there is a danger of exposure to radiation
• When in close proximity to power supply lines
adequate protection against noise by using noise filters,
etc.
installation in other equipment, the customer should
confirm conformity to EMC directives for the finished
product.
operation. It may otherwise be impossible to guarantee
safety due to unexpected malfunction or erroneous
operation.
damage and fire in the unit.
separate from power lines and high voltage lines.
Otherwise, this can cause malfunction.
damage to the unit due to excessive voltage or current.
heavy objects on them or allow them to be pinched. This
can cause broken lines.
Circuit uses the secondary coil of an isolated transformer as
the power supply, satisfying the following conditions.
• Max. voltage (with no load): 30 Vrms (42.4 V peak) or less
• Max. current: (1) 8 A or less (including shorts), and
peak) or less, and a power supply consisting of a class 2
power supply unit confirming to UL1310, or a class 2
transformer confirming to UL1585
Caution
Caution
Caution
Power Supply Safety Instructions
Safety Instructions for Cable
(2) When controlled by a circuit protector
(fuse, etc.) with the following rating
No-load voltage (V peak)
Over 20 [V] to 30 [V]
0 to 20 [V]
Series
Max. current rating
Peak voltage value
100
5.0
SV
1-2-11
SV
SZ
SY
SYJ
SX