VQZ115-5L1-N7 SMC Corporation, VQZ115-5L1-N7 Datasheet - Page 41

• Manufacturer Part Number: VQZ115-5L1-N7
• Description: Solenoid Valve, 3 port, body ported, 24VDC, L plug conn w/.3m lead, 1/4 fitting
• Manufacturer: SMC Corporation
• Type: Solenoidr

Specifications of VQZ115-5L1-N7

• Brand/series: VQZ Series
• Configuration: Base Mount
• Number Of Ports: 3
• Primary Type: Solenoid Valve
• Size, Port: 1⁄4"
• Voltage, Coil: 24 VDC
• Operating Pressure Range: 15-100 PSI (30-100 PSI For Three Position Valves)

1. EN-175301-803C (Former DIN 43650C)
2. Connection
3. Changing the entry direction
4. Precautions
5. Compatible cable
Tightening torque
0.2 to 0.25 N m
The DIN terminal type with an IP65 enclosure is protected
against dust and water, however, it must not be used in water.
1) Loosen the holding screw and pull the connector out of the
2) After removing the holding screw, insert a flat head screw-
3) Loosen the terminal screws (slotted screws) on the termi-
4) Secure the cord by fastening the ground nut.
After separating the terminal block and housing, the cord entry
can be changed by attaching the housing in the desired direc-
tion (4 directions at 90° intervals).
∗ When equipped with a light, be careful not to damage the
Plug in and pull out the connector vertically without tilting to
one side.
Cable O.D.: ø3.5 to ø7
(Reference) 0.5 mm
3306
Tightening torque
1.65 to 2.5 N m
light with the cord’s lead wires.
Ground nut
solenoid valve terminal block.
driver, etc. into the notch on the bottom of the terminal
block and pry it open, separating the terminal block and the
housing.
nal block, insert the cores of the lead wires into the termi-
nals according to the connection method, and fasten them
securely with the terminal screws.
Washer
(Rating symbol)
Refer to the table.
Grommet (Rubber)
How to Use DIN Terminal
Terminal screw
(3 locations)
Series
Specific Product Precautions 3
Be sure to read this before handling.
For Safety Instructions and 3 Port Solenoid Valve Precautions, refer to “Precautions for
Handling Pneumatic Devices” (M-03-E3A).
2
, 2-core or 3-core, equivalent to JIS C
VQZ
(Light mounting location)
Housing
Set screw
Terminal block
Notch
Tightening torque
0.3 to 0.4 N m
Without light
With light
Circuit diagram with light
Part no. for one-touch fitting for 1(P) port and silencer/one-touch
fitting for 3(R) port
The diameter of the above fitting and silencer is the maximum diameter to
in the EXH port.
Fitting and Silencer Part No. for P, R Ports
110 VAC (115 VAC)
220 VAC (230 VAC)
VQZ100
VQZ200
VQZ300
AC circuit
When Using Valve as an Individual Unit
Series
Rated voltage
Rated voltage
All voltages
NL
1
100 VAC
200 VAC
24 VDC
12 VDC
2
R
fitting for 1(P) port
NL: Neon light
(1) One-touch
DIN Connector Part No.
R: Resistor
KQ2S06-01S
KQ2H08-02S
KQ2H06-M5
(2) Silencer
Voltage symbol
Voltage symbol
100 V
200 V
110 V
220 V
None
24 V
12 V
DC circuit
LED
AN120-M5
INA-25-46
AN101-01
1
Silencer
2
R
(2) For 3(R) port
LED: Light emitting diode
SY100-82-3-05
SY100-82-3-06
SY100-82-2-01
SY100-82-2-02
SY100-82-2-03
SY100-82-2-04
(1) One-touch fitting
SY100-82-1
R: Resistor
IN-457-32 (for ø6)
Part no.
Part no.
One-touch fitting
Back page 4
KQ2H06-01S
KJS04-M5