AFM30-N03D-Z SMC Corporation, AFM30-N03D-Z Datasheet - Page 2

• Manufacturer Part Number: AFM30-N03D-Z
• Description: Mist Separator; Modular; 150 PSI max; 3/8NPT ports; auto drain (N.O.)
• Manufacturer: SMC Corporation

Specifications of AFM30-N03D-Z

• Body Size: 3⁄8 in.
• Diameter: 53 in.
• Height: 129 in.
• Material, Bowl: Polycarbonate
• Pressure, Operating: 0.05 MPa (Min.), 1.0 MPa (Max.)
• Proof Pressure: 1.5 MPa
• Size, Port: 3⁄8 in.
• Temperature, Ambient: -5 to +60 °C
• Thread Type: NPT
• Operating Pressure: 150 PSI

Flow Characteristics
Construction
Replacement parts
AFM20
AFM30, 40
Parts list
Note 1) Including O-Ring. Contact SMC regarding the bowl assembly supply for PSI and °F unit specifications.
Note 2) Bowl assembly for AFM30 to AFM40-06 includes a bowl guard (steel band material).
No.
No.
1
2
3
4
Description
Body
Element assembly
Bowl O-ring
Bowl assembly
Description
Flow rate L/min (ANR)
Zinc die-cast
IN
IN
AFM20
Note 1)
Drain
Drain
Material
NBR
PC
—
(Representative values)
AFM30, AFM40, AFM40-06
ø10 One-touch fitting
Material
OUT
AFM20P-060AS
C2SFP-260S
Aluminum die-cast
q
e
w
r
OUT
q
e
w
r
AFM20
C2SF
Float type auto drain (N.C.)
N.C.
AFM30P-060AS
C3SFP-260S
C3SF
ø10 One-touch fitting
Float type auto drain
AFM30
M5 x 0.8
Note 2)
Flow rate L/min (ANR)
Part no.
Platinum silver
AFM40P-060AS
C4SFP-260S
C4SF
Note
AFM40
N.O.
Note 2)
Mist Separator
AFM40P-060AS
C4SFP-260S
C4SF
AFM40-06
Note 2)
1. Install an air filter (Series AF) as a pre-
2. Do not install on the inlet side of the dry-
1. Replace the element every 2 years or
1. Design the system so that the mist sepa-
1. Do not allow air flow that exceeds the
2. Do not use in a low pressure application
liminary filter on the inlet side of the mist
separator to prevent premature clogging.
er as this can cause premature clogging
of the element.
when the pressure drop becomes
0.1MPa, whichever comes first, to pre-
vent damage to the element.
rator is installed in a pulsation-free loca-
tion. The difference between internal and
external pressure inside the element
should be kept within 0.1MPa, as ex-
ceeding this value could cause damage.
rated flow. If the air flow is allowed out-
side the range of the rated flow even mo-
mentarily, drainage and lubricant may
splash at the outlet side or cause dam-
age to the component.
(such as a blower). F.R.L. unit has its
own minimum operating pressure de-
pending on the equipment and is de-
signed specifically to function with com-
pressed air. If used below the minimum
operating pressure, a loss of perform-
ance and malfunction can occur. Contact
SMC if an application under such condi-
tions cannot be avoided.
Be sure to read before handling.
Refer to pages 75 through 78 for
safety instructions and F.R.L. unit
precautions.
Caution
Warning
Caution
Caution
AFM20/30/40
Specific Product Precautions
Maintenance
Flow rate L/min (ANR)
Air Supply
Selection
Design
: When saturated with oil
: Initial state
30