PIC16C711-04/P Microchip Technology Inc., PIC16C711-04/P Datasheet - Page 113

• Manufacturer Part Number: PIC16C711-04/P
• Description: 18 PIN, 1.75 KB OTP, 68 RAM, 13 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16C711-04/P

• A/d Inputs: 4-Channel, 8-Bit
• Cpu Speed: 5 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 13
• Memory Type: OTP
• Number Of Bits: 8
• Package Type: 18-pin PDIP
• Programmable Memory: 1.75K Bytes
• Ram Size: 68 Bytes
• Speed: 20 MHz
• Timers: 1-8-bit
• Voltage, Range: 2.5-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

13.1
DC CHARACTERISTICS
D001
D001A
D002*
D003
D004*
D005
D010
D013
D015
D020
D021
D021A
D021B
D023
Note 1: This is the limit to which V
Param.
1997 Microchip Technology Inc.
No.
*
† Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be
5: The
DC Characteristics:
These parameters are characterized but not tested.
and are not tested.
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all I
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to V
MCLR = V
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
estimated by the formula Ir = V
added to the base I
Supply Voltage
RAM Data Retention
Voltage (Note 1)
V
ensure internal Power-
on Reset signal
V
internal Power-on Reset
signal
Brown-out Reset Voltage B
Supply Current (Note 2)
Brown-out Reset Current
(Note 5)
Power-down Current
(Note 3)
Brown-out Reset Current
(Note 5)
DD
DD
start voltage to
rise rate to ensure
Characteristic
current is the additional current consumed when this peripheral is enabled. This current should be
DD
; WDT enabled/disabled as specified.
DD
or I
PD
DD
PIC16C715-04 (Commercial, Industrial, Extended)
PIC16C715-10 (Commercial, Industrial, Extended)
PIC16C715-20 (Commercial, Industrial, Extended))
DD
V
V
V
S
I
I
Sym
DD
PD
measurement.
can be lowered in SLEEP mode without losing RAM data.
DD
DR
POR
VDD
VDD
I
I
measurements in active operation mode are:
BOR
BOR
DD
/2Rext (mA) with Rext in kOhm.
Standard Operating Conditions (unless otherwise stated)
Operating temperature
0.05
Min Typ† Max Units
4.0
4.5
3.7
-
-
-
-
-
-
-
-
-
-
300* 500
300* 500
13.5
10.5
V
1.5
4.0
2.7
1.5
1.5
1.5
SS
-
-
-
5.5
5.5
4.3
30
42
21
24
30
5
-
-
-
V/ms See section on Power-on Reset for details
mA
mA
V
V
V
V
V
A
A
A
A
A
A
0˚C
-40˚C
-40˚C
XT, RC and LP osc configuration
HS osc configuration
Device in SLEEP mode
See section on Power-on Reset for details
BODEN configuration bit is enabled
XT, RC osc configuration (PIC16C715-04)
F
HS osc configuration (PIC16C715-20)
F
BOR enabled V
V
V
V
V
BOR enabled V
Applicable Devices
OSC
OSC
DD
DD
DD
DD
= 4.0V, WDT enabled, -40 C to +85 C
= 4.0V, WDT disabled, -0 C to +70 C
= 4.0V, WDT disabled, -40 C to +85 C
= 4.0V, WDT disabled, -40 C to +125 C
= 4 MHz, V
= 20 MHz, V
T
T
T
A
A
A
+70˚C (commercial)
+85˚C (industrial)
+125˚C (extended)
DD
DD
DD
PIC16C71X
Conditions
DD
DD
= 5.0V
= 5.0V
= 5.5V (Note 4)
= 5.5V
710 71 711 715
DS30272A-page 113
DD
and V
SS
.