PIC18F4620-E/P Microchip Technology Inc., PIC18F4620-E/P Datasheet - Page 44

• Manufacturer Part Number: PIC18F4620-E/P
• Description: 40 Pin, 64 KB Flash, 3968 RAM, 36 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F4620-E/P

• A/d Inputs: 13-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 1024 Bytes
• Input Output: 36
• Interface: SPI/I2C/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 64K Bytes
• Ram Size: 4K Bytes
• Speed: 40 MHz
• Timers: 1-8 bit, 3-16 bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18F2525/2620/4525/4620
REGISTER 4-1:
DS39626B-page 42
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
RCON: RESET CONTROL REGISTER
bit 7
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode)
SBOREN: BOR Software Enable bit
If BOREN1:BOREN0 = 01:
1 = BOR is enabled
0 = BOR is disabled
If BOREN1:BOREN0 = 00, 10 or 11:
Bit is disabled and read as ‘0’.
Unimplemented: Read as ‘0’
RI: RESET Instruction Flag bit
1 = The RESET instruction was not executed (set by firmware only)
0 = The RESET instruction was executed causing a device Reset (must be set in software after
TO: Watchdog Time-out Flag bit
1 = Set by power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-down Detection Flag bit
1 = Set by power-up or by the CLRWDT instruction
0 = Set by execution of the SLEEP instruction
POR: Power-on Reset Status bit
1 = A Power-on Reset has not occurred (set by firmware only)
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
BOR: Brown-out Reset Status bit
1 = A Brown-out Reset has not occurred (set by firmware only)
0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
Legend:
R = Readable bit
-n = Value at POR
R/W-0
Note 1: If SBOREN is enabled, its Reset state is ‘1’; otherwise, it is ‘0’.
Note 1: It is recommended that the POR bit be set after a Power-on Reset has been
IPEN
a Brown-out Reset occurs)
2: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming
2: The actual Reset value of POR is determined by the type of device Reset. See the
detected so that subsequent Power-on Resets may be detected.
that POR was set to ‘1’ by software immediately after POR).
notes following this register and Section 4.6 “Reset State of Registers” for
additional information.
SBOREN
R/W-1
(1)
U-0
Preliminary
—
W = Writable bit
‘1’ = Bit is set
(2)
(1)
R/W-1
RI
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R-1
TO
R-1
PD
 2004 Microchip Technology Inc.
x = Bit is unknown
R/W-0
POR
(2)
R/W-0
BOR
bit 0