PIC16F877-04I/P Microchip Technology Inc., PIC16F877-04I/P Datasheet - Page 89
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC16F877-04I/P
Manufacturer Part Number
PIC16F877-04I/P
Description
40 PIN, 7 KB FLASH, 368 RAM, 33 I/O, PDIP
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC16F877-04IP.pdf
(218 pages)
Specifications of PIC16F877-04I/P
A/d Inputs
8-Channel, 10-Bit
Comparators
2
Cpu Speed
5 MIPS
Eeprom Memory
256 Bytes
Frequency
20 MHz
Input Output
33
Interface
I2C/SPI/USART
Memory Type
Flash
Number Of Bits
8
Package Type
40-pin PDIP
Programmable Memory
14K Bytes
Ram Size
368 Bytes
Serial Interface
MSSP, USART
Speed
20 MHz
Timers
2-8-bit, 1-16-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F877-04I/P
Manufacturer:
MICROCHIP
Quantity:
3 000
Company:
Part Number:
PIC16F877-04I/PQ
Manufacturer:
MICROCHIP
Quantity:
1 000
Company:
Part Number:
PIC16F877-04I/PQ
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC16F877-04I/PT
Manufacturer:
BROADCOM
Quantity:
50
Company:
Part Number:
PIC16F877-04I/PT
Manufacturer:
MIC
Quantity:
36
Company:
Part Number:
PIC16F877-04I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
9.2.14
A STOP bit is asserted on the SDA pin at the end of a
receive/transmit by setting the Stop Sequence Enable
bit, PEN (SSPCON2<2>). At the end of a receive/
transmit, the SCL line is held low after the falling edge
of the ninth clock. When the PEN bit is set, the master
will assert the SDA line low. When the SDA line is sam-
pled low, the baud rate generator is reloaded and
counts down to 0. When the baud rate generator times
out, the SCL pin will be brought high, and one T
(baud rate generator rollover count) later, the SDA pin
will be de-asserted. When the SDA pin is sampled high
FIGURE 9-17:
2001 Microchip Technology Inc.
STOP CONDITION TIMING
SCL
SDA
Note: T
Write to SSPCON2
Falling edge of
9th clock
BRG
STOP CONDITION RECEIVE OR TRANSMIT MODE
ACK
= one baud rate generator period.
Set PEN
SDA asserted low before rising edge of clock
to setup STOP condition
T
T
BRG
BRG
BRG
T
SCL brought high after T
BRG
SCL = 1 for T
after SDA sampled high. P bit (SSPSTAT<4>) is set.
P
T
BRG
while SCL is high, the P bit (SSPSTAT<4>) is set. A
T
set (Figure 9-17).
Whenever the firmware decides to take control of the
bus, it will first determine if the bus is busy by checking
the S and P bits in the SSPSTAT register. If the bus is
busy, then the CPU can be interrupted (notified) when
a STOP bit is detected (i.e., bus is free).
9.2.14.1
If the user writes the SSPBUF when a STOP sequence
is in progress, then WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur).
BRG
BRG
PEN bit (SSPCON2<2>) is cleared by
later, the PEN bit is cleared and the SSPIF bit is
hardware and the SSPIF bit is set
, followed by SDA = 1 for T
BRG
WCOL Status Flag
PIC16F87X
BRG
DS30292C-page 87