TJA1041AT/VM,518 NXP Semiconductors, TJA1041AT/VM,518 Datasheet - Page 15

• Manufacturer Part Number: TJA1041AT/VM,518
• Description: IC CAN TRANSCEIVER HS 14-SOIC
• Manufacturer: NXP Semiconductors
• Type: Transceiverr

Specifications of TJA1041AT/VM,518

• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Number Of Drivers/receivers: 1/1
• Protocol: CAN
• Voltage - Supply: 4.75 V ~ 5.25 V
• Mounting Type: Surface Mount
• Product: Controller Area Network (CAN)
• Number Of Transceivers: 1
• Data Rate: 1 Mbps
• Supply Voltage (max): 5.25 V
• Supply Voltage (min): 4.75 V
• Supply Current (max): 80 mA
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Power Down Mode: Sleep/Standby
• Standard Supported: ISO 11898
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.75V
• Package Type: SO
• Supply Current: 80mA
• Operating Temperature (max): 125C
• Mounting: Surface Mount
• Pin Count: 14
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-4818-2; 935287963518

NXP Semiconductors
Table 8.
V
specified; all voltages are defined with respect to ground; positive currents flow into the device
[1]
11. Application information
TJA1041A_4
Product data sheet
Symbol
t
t
t
Thermal shutdown
T
BUSdom
BUSrec
wake
CC
j(sd)
= 4.75 V to 5.25 V; V
All parameters are guaranteed over the virtual junction temperature range by design, but only 100 % tested at T
wafer level and in addition to this, 100 % tested at T
parameters are only guaranteed with the reverse side of the die connected to ground.
Characteristics
Parameter
dominant time for wake-up
via bus
recessive time for wake-up
via bus
minimum wake-up time
after receiving a falling or
rising edge
shutdown junction
temperature
I/O
Fig 4.
= 2.8 V to V
…continued
BAT
Typical application with 3 V microcontroller
CC
; V
Conditions
standby or sleep mode; V
standby or sleep mode; V
standby or sleep mode; V
BAT
= 5 V to 27 V; R
amb
Rev. 04 — 29 July 2008
WAKE
= 125 C for cased products, unless specified otherwise. For bare dies, all
GND
9
2
10
13
V
CANH
BAT
CAN bus wires
TJA1041A
L
7
= 60 ; T
5 V
INH
BAT
BAT
BAT
11
SPLIT
= 12 V
= 12 V
= 12 V
3
V
vj
CC
= 40 C to +150 C; unless otherwise
3 V
12
CANL
Min
0.75
0.75
5
155
5
V
14
I/O
6
8
4
1
High-speed CAN transceiver
STB
EN
ERR
RXD
TXD
[1]
Typ
1.75
1.75
25
165
.
RXD
TXD
TJA1041A
CONTROLLER
Port x, y, z
amb
MICRO-
© NXP B.V. 2008. All rights reserved.
V
= 125 C for dies on
CC
Max
5
5
50
180
mnb116
15 of 25
Unit
C
s
s
s