ADM211AR Analog Devices Inc, ADM211AR Datasheet - Page 11
![IC TXRX RS-232 5V 0.1UF 28SOIC](/photos/6/59/65912/505-28-soic_sml.jpg)
ADM211AR
Manufacturer Part Number
ADM211AR
Description
IC TXRX RS-232 5V 0.1UF 28SOIC
Manufacturer
Analog Devices Inc
Type
Transceiverr
Datasheet
1.ADM211ARSZ.pdf
(16 pages)
Specifications of ADM211AR
Rohs Status
RoHS non-compliant
Number Of Drivers/receivers
4/5
Protocol
RS232
Voltage - Supply
4.5 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
28-SOIC (7.5mm Width)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADM211AR
Manufacturer:
Analog Devices Inc.
Quantity:
9 050
Part Number:
ADM211AR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADM211ARS
Manufacturer:
AD
Quantity:
5 510
Part Number:
ADM211ARS
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADM211ARS-REEL
Manufacturer:
ICS
Quantity:
227
Part Number:
ADM211ARS-REEL
Manufacturer:
AD
Quantity:
20 000
Company:
Part Number:
ADM211ARSREEL
Manufacturer:
FUJICOM
Quantity:
3 213
Part Number:
ADM211ARSZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADM211ARZ
Manufacturer:
AD
Quantity:
10 998
Part Number:
ADM211ARZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
GENERAL INFORMATION
The ADM206–ADM211/ADM213 family of RS-232 drivers/
receivers is designed to solve interface problems by meeting the
EIA-232-E specifications while using a single digital 5 V supply.
The EIA-232-E standard requires transmitters that will deliver
±5 V minimum on the transmission channel and receivers that
can accept signal levels down to ±3 V. The ADM206–ADM211/
ADM213 meet these requirements by integrating step-up voltage
converters and level shifting transmitters and receivers onto the
same chip. CMOS technology is used to keep the power dissi-
pation to an absolute minimum. A comprehensive range of
transmitter/receiver combinations is available to cover most
communication needs. The ADM206–ADM211/ADM213 are
modifications, enhancements, and improvements to the AD230–
AD241 family and derivatives thereof. They are essentially plug-
in compatible and do not have materially different applications.
The ADM206, ADM211, and ADM213 are particularly useful in
battery-powered systems because they feature a low power shut-
down mode that reduces power dissipation to less than 5 µW.
The ADM209 includes only a negative charge pump converter
and is intended for applications where a +12 V is available.
To facilitate sharing a common line or for connection to a
microprocessor data bus, the ADM206, the ADM209, the
ADM211, and the ADM213 feature an enable ( EN ) function.
When the receivers are disabled, their outputs are placed in a
high impedance state.
CIRCUIT DESCRIPTION
The internal circuitry in the ADM206–ADM211/ADM213
consists of three main sections: (a) a charge pump voltage
converter; (b) RS-232-to-TTL/CMOS receivers; and
(c) TTL/CMOS-to-RS-232 transmitters.
Charge Pump DC-to-DC Voltage Converter
The charge pump voltage converter consists of an oscillator and
a switching matrix. The converter generates a ±10 V supply
from the 5 V input. This is done in two stages using a switched
capacitor technique, as illustrated in Figure 22 and Figure 23.
First, the 5 V input supply is doubled to 10 V using capacitor
C1 as the charge storage element. The 10 V level is then
inverted to generate –10 V using C2 as the storage element.
OSCILLATOR
GND
INTERNAL
V
CC
Figure 22. Charge Pump Voltage Doubler
S1
S2
C1
+
S3
S4
C3
+
V+ = 2V
V
CC
CC
Rev. C | Page 11 of 16
Capacitors C3 and C4 are used to reduce the output ripple.
Their values are not critical and can be reduced if higher levels
of ripple are acceptable. The charge pump capacitors C1 and C2
may also be reduced at the expense of higher output impedance
on the V+ and V– supplies.
The V+ and V– supplies may also be used to power external
circuitry if the current requirements are small.
Transmitters (Drivers)
The drivers convert TTL/CMOS input levels into EIA-232-E
output levels. With V
load, the output voltage swing is ±9 V. Even under worst-case
conditions, the drivers are guaranteed to meet the ±5 V EIA-
232-E minimum requirement.
The input threshold levels are both TTL- and CMOS-compatible
with the switching threshold set at V
5 V, the switching threshold is 1.25 V typical. Unused inputs
may be left unconnected, because an internal 400 kΩ pull-up
resistor pulls them high, forcing the outputs into a low state.
As required by the EIA-232-E standard, the slew rate is limited
to less than 30 V/µs, without the need for an external slew
limiting capacitor, and the output impedance in the power-off
state is greater than 300 Ω.
Receivers
The receivers are inverting level shifters that accept EIA-232-E
input levels (±5 V to ±15 V) and translate them into 5 V TTL/
CMOS levels. The inputs have internal 5 kΩ pull-down resistors
to ground and are also protected against overvoltages of up to
±30 V. The guaranteed switching thresholds are 0.8 V minimum
and 2.4 V maximum, well within the ±3 V EIA-232-E require-
ment. The low level threshold is deliberately positive, since it
ensures that an unconnected input will be interpreted as a
low level.
The receivers have Schmitt-trigger inputs with a hysteresis level
of 0.65 V. This ensures error-free reception for both noisy
inputs and inputs with slow transition times.
Shutdown (SD)
The ADM206–ADM211/ADM213 feature a control input that
may be used to disable the part and reduce the power consump-
ion to less than 5 ΩW. This is very useful in battery-operated
systems. During shutdown, the charge pump is turned off, the
transmitters are disabled, and all receivers except R4 and R5 on
the ADM213 are put into a high impedance disabled state.
DOUBLER
VOLTAGE
FROM
OSCILLATOR
INTERNAL
GND
V+
Figure 23. Charge Pump Voltage Inverter
S1
S2
CC
ADM206–ADM211/ADM213
= +5 V and driving a typical EIA-232-E
C2
+
S3
S4
CC
/4. With a nominal V
C4
+
GND
V– = –(V+)
CC
=