DS3150QN Maxim Integrated Products, DS3150QN Datasheet - Page 9
![IC LIU T3/E3/STS-1 IND 28-PLCC](/photos/6/52/65249/406-28-plcc_sml.jpg)
DS3150QN
Manufacturer Part Number
DS3150QN
Description
IC LIU T3/E3/STS-1 IND 28-PLCC
Manufacturer
Maxim Integrated Products
Type
Line Interface Units (LIUs)r
Datasheet
1.DS3150T.pdf
(28 pages)
Specifications of DS3150QN
Number Of Drivers/receivers
1/1
Protocol
DS3
Voltage - Supply
3.135 V ~ 3.465 V
Mounting Type
Surface Mount
Package / Case
28-LCC, 28-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS3150QN
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
DS3150QN+
Manufacturer:
SYNQOR
Quantity:
124
Company:
Part Number:
DS3150QNB4TR
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
DS3150QNC1+
Manufacturer:
HALO
Quantity:
15 000
Company:
Part Number:
DS3150QNC1+
Manufacturer:
Maxim Integrated
Quantity:
10 000
§ A third consecutive zero (0, 0, 0)
In E3 mode, HDB3 decoding is performed. RLCV is asserted during any RCLK cycle where the data on
RNRZ causes one of the following code violations:
§ A BPV immediately preceded by a valid pulse (B, V) or by a valid pulse and a zero (B, 0, V)
§ A BPV with the same polarity as the last BPV
§ A fourth consecutive zero (0, 0, 0, 0)
When RLCV is asserted to flag a BPV, the RNRZ pin outputs a 1. The state bit that tracks the polarity of
the last BPV is toggled on every BPV, whether part of a valid B3ZS/HDB3 codeword or not.
To support a glueless interface to a variety of neighboring components, the polarity of RCLK can be
inverted using the ICE input pin. See the ICE pin description in
Receiver Jitter Tolerance. The receiver exceeds the input jitter tolerance requirements of all
applicable telecommunication standards in
Receiver Jitter Transfer. The jitter transfer performance of the receiver, with and without the jitter
attenuator enabled, is shown in
Figure 1-3. Receiver Jitter Tolerance
0.01
0.01
100
100
0.1
0.1
10
10
1
1
0.01
0.1
G.823 and
ETSI 300 689
GR-499 Cat II
DS3 JITTER TOLERANCE
0.1
E3 JITTER TOLERANCE
JA in Rx
FREQUENCY (kHz)
1
FREQUENCY (kHz)
JA in Rx
GR-499 Cat I
G.824
1
10
JA disabled
10
JA disabled
Figure
100
100
1-8.
1000
1000
Table
Note 1: All jitter tolerance curves are worst case over temperature,
Note 2: The low-frequency plateau seen in most of the jitter tolerance
Note 3: Receiver jitter tolerance is not tested during production test.
1-A. See the graphs in
9 of 28
0.01
100
0.1
voltage, cable length (0 to 900 feet), and RMON pin setting.
curves is not the actual performance of the DS3150 but rather
the limit of the measuring equipment (64 UI
tolerance in these low-frequency ranges is greater than or equal
to 64 UI
10
1
0.01
P-P
STS-1 JITTER TOLERANCE
.
GR-253-CORE
0.1
Table 2-A
JA in Rx
FREQUENCY (kHz)
1
Figure
for details.
10
JA disabled
1-3.
100
P-P
1000
). Actual jitter