AD9807JS Analog Devices Inc, AD9807JS Datasheet - Page 21
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9807JS
Manufacturer Part Number
AD9807JS
Description
IC CCD SIGNAL PROC 12BIT 64-PQFP
Manufacturer
Analog Devices Inc
Type
CCD Signal Processor, 12-Bitr
Specifications of AD9807JS
Rohs Status
RoHS non-compliant
Input Type
Logic
Output Type
Logic
Interface
Microprocessor
Current - Supply
86mA
Mounting Type
Surface Mount
Package / Case
64-MQFP, 64-PQFP
Operating Temperature (min)
0C
Operating Temperature (max)
70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
64
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD9807JS
Manufacturer:
ADI/亚德诺
Quantity:
20 000
CIS Application
Unlike many other integrated circuit CCD signal processors, the
AD9807/AD9805 can easily be implemented in imaging systems
that do not use a CCD. By disabling the input clamp and the
CDS blocks, any dc coupled signal within the input limits of the
part can be digitized. Figure 23 shows a typical block diagram of
the AD9807 used with a color CIS module, in this case Dyna
Image Corporation’s DL100*. The three color output signals
are dc coupled into the AD9807. The Dyna CIS module’s
output levels are around 70 mV to 500 mV dark to bright, well
within the input range of the AD9807. The AD9807 is config-
ured for 3-channel SHA operation through the MPU registers.
Timing used with the Dyna DL100 is shown in Figure 24; the
CIS output levels are sampled on the falling edge of CDSCLK1.
The digital ASIC shown can be implemented in a variety of
ways: it could include the MPU interface and timing generator,
as well as memory for the output data and pixel gain and offset
correction vectors.
Figure 23. CIS Application Diagram (Power, Ground, and
Decoupling Omitted)
*All trademarks are properties of their respective holders.
REV. 0
CIS
CLOCKS
CIS
GREEN
BLUE
RED
GENERATOR
VING
VINB
VINR
STRTLN,
CDSCLK1,
ADCCLK
TIMING
3
CDSCLK1
CDSCLK2
ADCCLK
STRTLN
GREEN
ANALOG INPUTS
CLOCK INPUTS
BLUE
RED
AD9807
GAIN<11:0>
OFFSET<7:0>
12
8
CORRECTION
CORRECTION
DOUT<11:0>
OFFSET
PIXEL
OEB, WRB
GAIN
A2, A1, A0
MPU<7:0>
RDB, CSB
PIXEL
Figure 25. Evaluation System Block Diagram
4
VING
VINR
VINB
CLOCKS
INTERFACE
7
12
MPU
DIGITAL
AD9807
ASIC
8
MPU CONTROL
AD9807 EVALUATION BOARD
OUTPUT
DATA
OFFSET
MPU I/O
DOUT
GAIN
+5V VOLT
POWER
SUPPLY
–21–
8
12
8
7
EVALUATION BOARDS
The AD9807 and AD9805 evaluation boards are designed to
provide an easy interface to a standard PC, simplifying the task
of evaluating the performance of the AD9807/AD9805 with an
existing imaging system. The system level block diagram shown
in Figure 25 illustrates the basic evaluation setup for the
AD9807 (the AD9805 is the same). The user needs to supply
the analog input signals (such as outputs from a CCD), the
AD9807/AD9805’s clock signals, a power supply and a printer
cable to connect the evaluation board to the PC’s parallel port.
Software is included to allow the user to easily accomplish three
major tasks: first, configure the AD9807/AD9805 in one of several
operating modes (1 Channel, 3 Channel, CDS or SHA mode,
etc.), second, acquire output data from the part and third, down-
load pixel gain and offset correction data to the evaluation board
and enable pixel rate shading and offset correction.
Figures 26 and 27 show the signal routing and decoupling for
the AD9807 evaluation board.
The evaluation boards are designated with the part numbers
AD9807-EB and AD9805-EB.
12
CIS START PULSE
CIS OUTPUT
CIS CLOCK
BUFFERS,
LATCHES,
CONTROL
CDSCLK1
LOGIC
ADCCLK
STRTLN
FIFO
AND
Figure 24. CIS Application Timing Signals
8
PRINTER
CABLE
PC
PARALLEL
PORT
AD9807/AD9805