PCA9541D/03,112 NXP Semiconductors, PCA9541D/03,112 Datasheet - Page 36
![IC I2C 2:1 SELECTOR 16SOIC](/photos/6/52/65286/16-soic_sot109-1_sml.jpg)
PCA9541D/03,112
Manufacturer Part Number
PCA9541D/03,112
Description
IC I2C 2:1 SELECTOR 16SOIC
Manufacturer
NXP Semiconductors
Datasheet
1.PCA9541BS03118.pdf
(41 pages)
Specifications of PCA9541D/03,112
Package / Case
16-SOIC (3.9mm Width)
Applications
2-Channel I²C Multiplexer
Interface
I²C, SMBus
Voltage - Supply
2.3 V ~ 5.5 V
Mounting Type
Surface Mount
Logic Family
PCA9541
Operating Supply Voltage
2.3 V to 5.5 V
Power Dissipation
400 mW
Operating Temperature Range
- 40 C to + 85 C
Input Voltage
7 V
Logic Type
I2C Bus
Maximum Clock Frequency
400 KHz
Mounting Style
SMD/SMT
Output Current
25 mA
Output Voltage
2.3 V to 5.5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
935273317112
PCA9541D/03
PCA9541D/03
PCA9541D/03
PCA9541D/03
NXP Semiconductors
16. Soldering of SMD packages
PCA9541_7
Product data sheet
16.1 Introduction to soldering
16.2 Wave and reflow soldering
16.3 Wave soldering
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description” .
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
Key characteristics in wave soldering are:
•
•
•
•
•
•
•
•
•
•
Through-hole components
Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus SnPb soldering
Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
Solder bath specifications, including temperature and impurities
Rev. 07 — 2 July 2009
2-to-1 I
2
C-bus master selector with interrupt logic and reset
PCA9541
© NXP B.V. 2009. All rights reserved.
36 of 41