EK43701-01 Peregrine Semiconductor, EK43701-01 Datasheet
EK43701-01
Specifications of EK43701-01
Related parts for EK43701-01
EK43701-01 Summary of contents
Page 1
... A0 A1 Document No. 70-0243-06 │ www.psemi.com Features RF Output A2 P/S ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. Product Specification PE43701 50 Ω RF Digital Attenuator 7-bit, 31.75 dB, 9 kHz - 4.0 GHz HaRP™-enhanced UltraCMOS™ device Attenuation: 0.25 dB steps to 31.75 dB High Linearity: Typical +59 dBm IIP3 Excellent low-frequency performance 3 ...
Page 2
... State 1.5 1.0 0.5 0.0 -0.5 -1.0 -1.5 0 1000 2000 Frequency (MHz) ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page 3 5 Frequency 9 kHz ≤ 4 GHz 9 kHz < 3 GHz 9 kHz < 3 GHz 3 GHz ≤ 4 GHz 9 kHz - 4 GHz 9 kHz - 4 GHz 20 MHz - 4 GHz ...
Page 3
... T = +25C 0dB 0.25dB 0.5dB 4dB 8dB 16dB Frequency (GHz) 16dB State -40C 25C Frequency (GHz) 0dB 0.25dB 0.5dB 1dB 4dB 8dB 16dB 31.75dB Frequency (GHz) ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. 1dB 2dB 31.75dB 85C 2dB Page ...
Page 4
... Frequency (MHz) ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page Figure 14. Attenuation Error vs. Attenuation 3000 MHz 1.5 1.0 0.5 0.0 -0.5 -1.0 -1.5 0 Figure 16. Attenuation Error vs. Attenuation +85 C 1.5 1.0 0.5 0.0 -0 ...
Page 5
... Switching rate is defined to be the speed at which the DSA can be toggled across attenuation states. Description Exposed Solder Pad Connection The exposed solder pad on the bottom of the package must be grounded for proper device operation. ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page ...
Page 6
... Note 1. Input leakage current per Control pin Figure 19. Maximum Power Handling Capability: Z 30.0 25.0 20.0 15.0 10.0 5.0 0.0 1.0E+03 1.0E+04 1.0E+05 ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page Table 4. Absolute Maximum Ratings Max Units Symbol V V Power supply voltage DD 5.5 V ...
Page 7
... Table 8. Address Word Truth Table A7 (MSB Function Table 9. Attenuation Word Truth Table Attenuation Setting RF1-RF2 L L Reference 31.75 dB Bits can either be set to logic high or logic low *D7 must be set to logic low Q10 *D7 D6 ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. Address Word ...
Page 8
... CLK inputs allow data to be serially entered into the shift register. Serial data is clocked in LSB first, beginning with the Attenuation Word. ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page The shift register must be loaded while LE is held LOW to prevent the attenuator value from changing as data is entered ...
Page 9
... Parallel data hold time DIH Parallel/Serial setup time PSSU T Parallel/Serial hold time PSIH Digital register delay T PD (internal) Digital register delay T DIPD (internal, direct mode only) ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. T DIH T AIH T PSIH T LESU T LEPW T PD VALID Min ...
Page 10
... LE from and back latch the DD programming word into the DSA. LE must be logic low prior to programming the next word. ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page Figure 22. Evaluation Board Layout Peregrine Specification 101-0312 Note: Reference Fig. 23 for Evaluation Board Schematic Serial-Addressable Programming Procedure Position the Parallel/Serial (P̅ ...
Page 11
... Peregrine Specification 102-0381 Figure 24. Package Drawing QFN 5x5 mm MAX A NOM MIN Document No. 70-0243-06 │ www.psemi.com Note: Capacitors C1-C8, C13, & C14 may be omitted. On the PE43701 pin 20 (shown as V 0.900 0.850 0.800 ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. ) must be grounded. SS Page ...
Page 12
... ZZZZZ Table 13. Ordering Information Order Code Part Marking PE43701MLI 43701 PE43701MLI-Z 43701 PE43701 G – 32QFN 5x5mm-3000C EK43701-01 43701 ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page Tape Feed Direction YYWW = Date Code ZZZZZ = Last five digits of Lot Number Description PE43701 G - 32QFN 5x5mm-75A PE43701 G – ...
Page 13
... Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS, HaRP, MultiSwitch and DuNE are trademarks of Peregrine Semiconductor Corp. ©2008-2009 Peregrine Semiconductor Corp. All rights reserved. Page ...