ACS706ELC-05C Allegro Microsystems Inc, ACS706ELC-05C Datasheet - Page 2

• Manufacturer Part Number: ACS706ELC-05C
• Description: SENSOR CURRENT 5A 5V BI 8-SOIC
• Manufacturer: Allegro Microsystems Inc
• Series: -r

Specifications of ACS706ELC-05C

• Current - Sensing: ±5A
• Accuracy: ±1%
• Sensitivity: 133mV/A
• Current - Supply: 8mA
• Sensor Type: Hall Effect
• Voltage - Supply: 4.5 V ~ 5.5 V
• Output: 2.5V
• Frequency: 50kHz
• Response Time: 6µs
• Polarization: Bidirectional
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 620-1164-2; ACS706ELC-005

*
ACS706ELC05C-DS, Rev. 3
Junction Temperature, T
Supply Voltage, V
Reverse Supply Voltage, V
Output Voltage, V
Reverse Output Voltage, V
Output Current Source, I
Output Current Sink, I
Maximum Transient Sensed Current
Operating Temperature,
Storage Temperature, T
Nominal Operating Temperature, T
Overcurrent Transient Tolerance*, I
*
1 pulse every 100 seconds.
100 total pulses, 250 ms duration each, applied at a rate of
Pin 1: IP+
AB SO LUTE MAX I MUM RAT INGS
Pin 2: IP+
Pins 6 and 7 are internally connected in shipping
product. For compatibility with future devices,
leave pin 6 floating.
Maximum Junction, T
Pin 3: IP–
Range E ............................................ –40 to 85ºC
Pin 4: IP–
Bidirectional 1.5 mΩ Hall Effect Based Linear Current Sensor
OUT
CC
Package LC
.......................................... 16 V
J
........................................ 16 V
OUT(Sink)
< T
S
TÜV America
Certificate Number:
U8V 04 12 54214 005
OUT(Source)
...................... –65 to 170°C
J(max)
J(max)
ROUT
RCC
.
........................ –16 V
.......................10 mA
....................... 165°C
...................... –0.1 V
A
................. 3 mA
*
P
, I
Pin 8: VCC
................ 60 A
R(max)
Pin 7: VOUT
Pin 6: N.C.
Pin 5: GND
with Voltage Isolation and 15 A Dynamic Range
... 100 A
ACS706ELC-05C
The Allegro ACS706 family of current sensor ICs provides economical and
precise solutions for current sensing in industrial, automotive, commercial, and
communications systems. The device package allows for easy implementation
by the customer. Typical applications include motor control, load detection and
management, switch-mode power supplies, and overcurrent fault protection.
The device consists of a precision, low-offset linear Hall circuit with a copper
conduction path located near the surface of the die. Applied current flowing
through this copper conduction path generates a magnetic field which the Hall
IC converts into a proportional voltage. Device accuracy is optimized through
the close proximity of the magnetic signal to the Hall transducer. A precise,
proportional voltage is provided by the low-offset, chopper-stabilized BiCMOS
Hall IC, which is programmed for accuracy at the factory.
The output of the device has a positive slope (>V
flows through the primary copper conduction path (from pins 1 and 2, to pins 3
and 4), which is the path used for current sampling. The internal resistance of this
conductive path is typically 1.5 mΩ, providing low power loss. The thickness
of the copper conductor allows survival of the device at up to 5× overcurrent
conditions. The terminals of the conductive path are electrically isolated from the
signal leads (pins 5 through 8). This allows the ACS706 to be used in applications
requiring electrical isolation without the use of opto-isolators or other costly
isolation techniques.
The ACS706 is provided in a small, surface mount SOIC8 package. The leadframe
is plated with 100% matte tin, which is compatible with standard lead (Pb) free
printed circuit board assembly processes. Internally, the flip-chip uses high-
temperature Pb-based solder balls, currently exempt from RoHS. The device is
fully calibrated prior to shipment from the factory.
Features and Benefits
•
• 1.5 mΩ internal conductor resistance
• 1600 V
• 4.5 to 5.5 V, single supply operation
• 50 kHz bandwidth
• 133 mV/A output sensitivity and 15 A dynamic range
• Output voltage proportional to ac and dc currents
• Factory-trimmed for accuracy
• Extremely stable output offset voltage
• Near-zero magnetic hysteresis
• Ratiometric output from supply voltage
Use the following complete part number when ordering:
Small footprint, low-profile SOIC8 package
RMS
minimum isolation voltage between pins 1-4 and 5-8
ACS706ELC-05C
Part Number
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 [phone]
www.allegromicro.com
SOIC8 surface mount
CC
Package
/ 2) when an increasing current