DG441DYZ Intersil, DG441DYZ Datasheet
DG441DYZ
Specifications of DG441DYZ
Available stocks
Related parts for DG441DYZ
DG441DYZ Summary of contents
Page 1
... Automatic Test Equipment CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 DG441, DG442 FN3281. <1.6mW D (Max 250ns (Max, DG441 120ns | Intersil (and design trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002-2006. All Rights Reserved ...
Page 2
... Ordering Information PART NUMBER PART MARKING DG441DJ DG441DJ DG441DJZ (Note) DG441DJZ DG441DY DG441DY DG441DY-T DG441DY DG441DYZ (Note) DG441DYZ DG441DYZ-T (Note) DG441DYZ DG441DYZA (Note) DG441DYZ DG441DYZA-T (Note) DG441DYZ DG441DVZ (Note) DG441DVZ DG441DVZ-T (Note) DG441DVZ DG442DJ DG442DJ DG442DJZ (Note) DG442DJZ DG442DY DG442DY DG442DY-T ...
Page 3
Schematic Diagram (One Channel GND 1 PER DIE COMMON TO EVERY CHANNEL V- Pin Descriptions PIN SYMBOL GND ...
Page 4
Absolute Maximum Ratings ...
Page 5
Electrical Specifications (Dual Supply) Test Conditions +15V -15V, V Unless Otherwise Specified (Continued) PARAMETER POWER SUPPLY CHARACTERISTICS Positive Supply Current, I+ Negative Supply Current, I- Ground Current, I GND Electrical Specifications (Single Supply) Test Conditions: V+ ...
Page 6
Test Circuits and Waveforms V is the steady state output with the switch on. Feedthrough via switch capacitance may result in spikes at the leading and trailing O edge of the output waveform. 3V LOGIC 50% INPUT 0V t OFF ...
Page 7
Test Circuits and Waveforms FIGURE 5. SOURCE/DRAIN CAPACITANCES TEST CIRCUIT Application Information GAIN ERROR IS DETERMINED ONLY BY THE RESISTOR TOLERANCE. OP AMP OFFSET AND CMRR WILL LIMIT ACCURACY OF CIRCUIT. +15V -15V FET INPUT AMP 3 ...
Page 8
Typical Performance Curves 100 - (V) D FIGURE AND POWER SUPPLY VOLTAGE DS(ON) D 140 120 +125°C +85°C 100 80 +25°C 60 0°C 40 -40°C -55° ...
Page 9
Typical Performance Curves 140 120 100 80 OFF ISOLATION +15V -15V P = 10dBm GEN 0 100 1k 10k 100k FREQUENCY (Hz) FIGURE 14. CROSSTALK AND OFF ISOLATION vs FREQUENCY 160 V+ = ...
Page 10
Typical Performance Curves +15V V- = -15V S(ON) D(ON S(OFF) D(OFF -15 - (V) A FIGURE 20. SOURCE/DRAIN CAPACITANCE vs ANALOG VOLTAGE 10 ...
Page 11
Die Characteristics DIE DIMENSIONS: 2160μm x 1760μm x 485μm METALLIZATION: Type: SiAl ±1k Å Å Thickness: 12k Metallization Mask Layout S ( (4) GND ( DG441, DG442 PASSIVATION: Type: Nitride Thickness: 8k WORST CASE ...
Page 12
Dual-In-Line Plastic Packages (PDIP INDEX N/2 AREA -B- -A- D BASE PLANE -C- SEATING PLANE 0.010 (0.25 NOTES: 1. Controlling Dimensions: INCH. In case of conflict between ...
Page 13
Small Outline Plastic Packages (SOIC) N INDEX 0.25(0.010) H AREA E - SEATING PLANE - -C- α 0.10(0.004) 0.25(0.010 NOTES: 1. Symbols are defined in the ...
Page 14
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...