W29EE512T-70 Winbond Electronics, W29EE512T-70 Datasheet
W29EE512T-70
Specifications of W29EE512T-70
Available stocks
Related parts for W29EE512T-70
W29EE512T-70 Summary of contents
Page 1
... GENERAL DESCRIPTION The W29EE512 is a 512K bit, 5-volt only CMOS flash memory organized as 64K can be programmed and erased in-system with a standard 5V power supply. A 12-volt V required. The unique cell architecture of the W29EE512 results in fast program/erase operations with extremely low current consumption (compared to other comparable 5-volt flash memory products). The device can also be programmed and erased using standard EPROM programmers ...
Page 2
PIN CONFIGURATIONS # 32-pin 8 A4 PLCC ...
Page 3
FUNCTIONAL DESCRIPTION Read Mode The read operation of the W29EE512 is controlled by #CE and #OE , both of which have to be low for the host to obtain data from the outputs. #CE is used for device selection. When ...
Page 4
Hardware Data Protection The integrity of the data stored in the W29EE512 is also hardware protected in the following ways: (1) Noise/Glitch Protection: A #WE pulse of less than duration will not initiate a write cycle. (2) ...
Page 5
TABLE OF OPERATING MODES Operating Mode Selection (Operating Range = (Ambient Temperature), V MODE Read Write Standby Write Inhibit Output Disable 5-Volt Software Chip Erase Product 10 #CE #OE #WE ...
Page 6
Command Codes for Software Data Protection BYTE SEQUENCE TO ENABLE PROTECTION ADDRESS 0 Write 1 Write 2 Write 3 Write 4 Write 5 Write Software Data Protection Acquisition Flow (Optional page-load operation) Notes for software program code: Data Format: DQ7 ...
Page 7
Command Codes for Software Chip Erase BYTE SEQUENCE 0 Write 1 Write 2 Write 3 Write 4 Write 5 Write Software Chip Erase Acquisition Flow Notes for software chip erase: Data Format: DQ7 DQ0 (Hex) Address Format: A14 A0 (Hex) ...
Page 8
Command Codes for Product Identification BYTE ALTERNATE SOFTWARE (5) SEQUENCE PRODUCT IDENTIFICATION ENTRY ADDRESS 0 Write 5555H 1 Write 2AAAH 2 Write 5555H 3 Write - 4 Write - 5 Write - Pause 10 S Software Product Identification Acquisition Flow ...
Page 9
DC CHARACTERISTICS Absolute Maximum Ratings PARAMETER Power Supply Voltage to V Potential ss Operating Temperature Storage Temperature D.C. Voltage on Any Pin to Ground Potential except A9 Transient Voltage (¡ Õ nS) on Any Pin to Ground Potential ...
Page 10
Power-up Timing PARAMETER Power-up to Read Operation Power-up to Write Operation CAPACITANCE (V = 5.0V MHz PARAMETER I/O Pin Capacitance Input Capacitance AC CHARACTERISTICS AC Test Conditions PARAMETER Input Pulse Levels ...
Page 11
Read Cycle Timing Parameters ( 5.0 5 for 70 nS PARAMETER Read Cycle Time Chip Enable Access Time Address Access Time Output Enable Access Time #CE High to High-Z Output #OE ...
Page 12
Polling Characteristics PARAMETER Data Hold Time #OE Hold Time (2) #OE to Output Delay Write Recovery Time Notes: (1) These parameters are characterized and not 100% tested. (2) See T spec in A.C. Read Cycle Timing Parameters OE Toggle ...
Page 13
TIMING WAVEFORMS Read Cycle Timing Diagram Address A15-0 #CE #OE V #WE High-Z DQ7-0 #WE Controlled Write Cycle Timing Diagram T AS Address A15-0 # OES #OE #WE DQ7 ...
Page 14
Timing Waveforms, continued #CE Controlled Write Cycle Timing Diagram Address A15-0 #CE #OE #WE High Z DQ7-0 Page Write Cycle Timing Diagram Address A15-0 DQ7-0 #CE #OE # OES T OEH T ...
Page 15
Timing Waveforms, continued #DATA Polling Timing Diagram Address A15-0 #WE # DQ7 Toggle Bit Timing Diagram #WE #CE T OEH # DQ6 OEH HIGH HIGH-Z Publication Release Date: February 18, ...
Page 16
Timing Waveforms, continued Page Write Timing Diagram Software Data Protection Mode software data protection mode Address A15-0 5555 DQ7-0 AA #CE # #WE SW0 Reset Software Data Protection Timing Diagram Address A15-0 5555 DQ7-0 #CE #OE T #WE ...
Page 17
Timing Waveforms, continued 5-Volt-only Software Chip Erase Timing Diagram Address A15-0 5555 DQ7-0 AA #CE # #WE SW0 Six-byte code for 5V-only software chip erase 2AAA 5555 2AAA 5555 BLC T WPH SW2 SW3 ...
Page 18
... W29EE512T-12 120 W29EE512Q-70 70 W29EE512Q-90 90 W29EE512P-70B 70 W29EE512P-90B 90 W29EE512P-12B 120 W29EE512T-70B 70 W29EE512T-90B 90 W29EE512T-12B 120 W29EE512Q-70B 70 W29EE512Q-90B 90 Notes: 1. Winbond reserves the right to make changes to its products without prior notice. 2. Purchasers are responsible for performing appropriate quality assurance testing on products intended for use in applications where personal injury might occur as a consequence of product failure. ...
Page 19
HOW TO READ THE TOP MARKING Example: The top marking of 32L-PLCC W29EE512P-70B W29EE512P-70B 2138977A-A12 149OBRA st 1 line: winbond logo nd 2 line: the part number: W29EE512P-70B rd 3 line: the lot number th 4 line: the tracking code: ...
Page 20
... Notes: 1. Dimensions D & not include interlead flash. 2. Dimension b does not include dambar protrusion/intrusion. 3. Controlling dimension: Inches. 4. General appearance spec. should be based on fina visual inspection sepc. Dimension In Inches Dimension In mm Symbol Min. Nom. Min. ...
Page 21
Package Dimensions, continued 32-pin VSOP 0.10(0.004 Publication Release Date: February 18, 2002 - 21 - W29EE512 Dimension In Inches Dimension In mm Symbol Max. Min. Nom. Max. Min. Nom. ...
Page 22
... Yokohama, 222-0033 TEL: 81-45-4781881 FAX: 81-45-4781800 - 22 - W29EE512 DESCRIPTION Winbond Electronics (Shanghai) Ltd. 27F, 2299 Yan An W. Rd. Shanghai, 200336 China TEL: 86-21-62365999 FAX: 86-21-62365998 Winbond Electronics (H.K.) Ltd. Unit 9-15, 22F, Millennium City, No. 378 Kwun Tong Rd., Kowloon, Hong Kong TEL: 852-27513100 FAX: 852-27552064 ...