LH28F160BGE-BTL10 Sharp Electronics, LH28F160BGE-BTL10 Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/6/602/sharp_electronics_sml.jpg)
LH28F160BGE-BTL10
Manufacturer Part Number
LH28F160BGE-BTL10
Description
Manufacturer
Sharp Electronics
Datasheet
1.LH28F160BGE-BTL10.pdf
(36 pages)
Specifications of LH28F160BGE-BTL10
Cell Type
NOR
Density
16Mb
Access Time (max)
100ns
Interface Type
Parallel
Boot Type
Bottom
Address Bus
20b
Operating Supply Voltage (typ)
3.3V
Operating Temp Range
0C to 70C
Package Type
TSOP-I
Sync/async
Asynchronous
Operating Temperature Classification
Commercial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
16b
Number Of Words
1M
Supply Current
30mA
Mounting
Surface Mount
Pin Count
48
Lead Free Status / Rohs Status
Not Compliant
4.1 Read Array Command
Upon initial device power-up and after exit from
deep power-down mode, the device defaults to
read array mode. This operation is also initiated by
writing the Read Array command. The device
remains enabled for reads until another command
is written. Once the internal WSM has started a
block erase or word write, the device will not
recognize the Read Array command until the WSM
completes its operation unless the WSM is
suspended via an Erase Suspend or Word Write
Suspend command. The Read Array command
functions independently of the V
RP# can be V
4.2 Read Identifier Codes Command
The identifier code operation is initiated by writing
the Read Identifier Codes command. Following the
command write, read cycles from addresses shown
in Fig. 2 retrieve the manufacture and device codes
(see Table 3 for identifier code values). To
terminate the operation, write another valid
command. Like the Read Array command, the
Read
independently of the V
V
command, the following information can be read :
4.3 Read Status Register Command
The status register may be read to determine when
a block erase or word write is complete and
whether the operation completed successfully. It
may be read at any time by writing the Read Status
Register command. After writing this command, all
subsequent read operations output data from the
status register until another valid command is
written. The status register contents are latched on
Device Code (Top Boot)
Device Code (Bottom Boot)
IH
or V
Manufacture Code
Identifier
HH
. Following the Read Identifier Codes
CODE
Table 3 Identifier Codes
IH
or V
Codes
HH
PP
.
voltage and RP# can be
command
ADDRESS
00B0H
0068H
0069H
PP
voltage and
functions
00000H
00001H
00001H
DATA
- 12 -
the falling edge of OE# or CE#, whichever occurs.
OE# or CE# must toggle to V
to update the status register latch. The Read Status
Register command functions independently of the
V
4.4 Clear Status Register Command
Status register bits SR.5, SR.4, SR.3 or SR.1 are
set to "1"s by the WSM and can only be reset by
the Clear Status Register command. These bits
indicate various failure conditions (see Table 5). By
allowing system software to reset these bits,
several operations (such as cumulatively erasing
multiple blocks or writing several words in
sequence) may be performed. The status register
may be polled to determine if an error occurred
during the sequence.
To clear the status register, the Clear Status
Register command (50H) is written. It functions
independently of the applied V
be V
during block erase or word write suspend modes.
4.5 Block Erase Command
Erase is executed one block at a time and initiated
by a two-cycle command. A block erase setup is
first written, followed by a block erase confirm.
This command sequence requires appropriate
sequencing and an address within the block to be
erased (erase changes all block data to FFFFH).
Block preconditioning, erase, and verify are handled
internally by the WSM (invisible to the system).
After the two-cycle block erase sequence is written,
the device automatically outputs status register data
when read (see Fig. 3). The CPU can detect block
erase completion by analyzing the output data of
the RY/BY# pin or status register bit SR.7.
When the block erase is complete, status register
bit SR.5 should be checked. If a block erase error
is detected, the status register should be cleared
before system software attempts corrective actions.
PP
voltage. RP# can be V
IH
or V
HH
. This command is not functional
LH28F160BG-TL/BGH-TL
IH
IH
or V
PP
before further reads
HH
voltage. RP# can
.